Upright X Series Скачать руководство пользователя страница 15

Страница: 15 / 164

Page 2-3

Operation and Specifications

2.2 - Pre-Operation and Safety Inspection

X Series Work Platform

Figure 2-2: Emergency Lowering

19. Pull out on the Emergency Lower-

ing Knob to check for proper oper-
ation. Once the platform has
lowered, release the knob.

20. Push the Chassis Emergency Stop

Switch to check for proper opera-
tion. All the machine functions
should be disabled. Pull out the
Emergency Stop Switch to
resume.

21. Turn the Chassis Key Switch to

DECK.

22. Check that the route is clear of

obstacles (persons, obstructions,
holes, drop-offs, bumps, and
debris), is level, and capable of
supporting the wheel loads.

23. Mount the platform and properly

close the entrance.

Figure 2-3: Platform Controls

24. PLATFORM CONTROLS, Turn Lift/

Drive Switch to DRIVE.

NOTE:

Use both HI and LOW drive (if

applicable) when performing the following
steps.

25. Engage the Interlock Switch and

move the Control Handle FOR-
WARD, then REVERSE, to check
for speed control.

26. Push the Steering Switch RIGHT,

then LEFT, to check for steering
control.

27. Turn the Lift/Drive Switch to LIFT.

28. Engage the Interlock Switch and

move the Control Handle forward to
check platform lift controls. Raise
the platform to full elevation.

29. Pull back on the Control Handle.

The platform should descend and
the audible lowering alarm should
sound.

30. Lower the platform completely.

31. Push the Platform Emergency Stop

Switch to check for proper operation. All the machine functions should be disabled. Pull out
the Platform Emergency Stop Switch to resume.

Emergency Lowering Knob

Control

Handle with

Interlock

Switch

LIFT/ DRIVE

Switch

Platform EMERGENCY

STOP Switch

Steering

Switch

060571-005

Содержание X Series





































































































































































Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды

Upright X Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды