Upright X Series Скачать руководство пользователя страница 31

Страница: 31 / 164

Page 3-3

Maintenance

3.4 - UpRight Connectors

X Series Work Platform

ALE

ONNECTOR

LUG

)

1. Disconnect the male connector (plug) from the female connector (receptacle).

2. Using the flat end of the Removal Tool (or flat blade screwdriver), pry the Locking Wedge

from the Male Connector. Care should be taken that the Silicon Gasket is not damaged dur-
ing this procedure.

3. Check all parts for damage. Replace all parts which are damaged or worn.

4. Replace or recrimp the wires and contacts. Refer to “Crimping” procedure.

EMALE

ONNECTOR

ECEPTACLE

)

1. Disconnect the male connector (plug) from the female connector (receptacle).

2. Using the notched end of the Removal Tool (or a wire hook), pull the Locking Wedge from

the Female Connector.

3. Check all parts for damage. Replace all parts which are damaged or worn.

4. Replace or recrimp the wires and contacts. Refer to “Crimping” procedure.

ELEASING

OCKING

INGERS

Figure 3-3: Locking Finger, UpRight Connector

1. The Locking Fingers can be released

following the removal of the Locking
Wedge of either the male or female
connector.

2. Use the removal tool (or flat bladed

screwdriver) to push the Locking Fin-
gers aside. This will release the grip
on the contact.

3. Pull the wire and contact out of the

connector.

RIMPING

NOTE:

Complete crimping instructions are included in each Field Kit.

1. Strip ¼” (6 mm) from the wire.

2. Insert the contact into the crimping tool.

3. Insert the stripped wire into the contact. Copper strands should be visible in the bleed hole

of the contact, and no copper strands should be loose (outside) of the contact barrel.

4. Completely close the handles of the crimping tool. Release the handles of the crimping tool

and remove the crimped contact.

5. Inspect the crimped contact to ensure that all strands are secure in the crimp barrel.

EMOVING

ONTACT

FROM

EAVY

UTY

LUG

Figure 3-4: Heavy Duty UpRight Connector

1. Slip the removal tool along the wire to

be replaced.

2. Push the removal tool into the connec-

tor until the contact is released.

3. Pull the wire and contact out of the

plug.

060571-005

Содержание X Series





































































































































































Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды

Upright X Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды