Upright X Series Скачать руководство пользователя страница 39

Страница: 39 / 164

Page 3-11

Maintenance

3.9 - Hydraulic Oil Tank and Filter

X Series Work Platform

3.9 H

YDRAULIC

ANK

AND

ILTER

LUID

EVEL

With the platform fully lowered, open the left module and remove the reservoir breather/cap. Oil
should be at the full mark.

AND

ILTER

EPLACEMENT

1. Operate the work platform for 10-15 minutes to bring the hydraulic oil up to normal operating

temperature.

Figure 3-14: Oil Filter

2. Provide a suitable container to catch the

drained oil. Hydraulic tank has a 5 gallon
(19 L) capacity.

3. Open left module door.

4. Remove the drain plug and allow all the

oil to drain. Dispose of hydraulic fluid
properly (contact your local oil recycler).

5. Reinstall the drain plug.

6. Unscrew the filter from the filter assem-

bly.

7. Apply a thin film of clean hydraulic oil

(ISO #46) to the gasket of the replace-
ment filter.

8. Screw the replacement filter onto the filter

head until the gasket makes contact,
then turn the filter 3/4 of a turn further.

9. Fill the hydraulic reservoir with ISO #46 hydraulic oil until the oil is up to the full mark on the

dipstick.

ESERVOIR

REATHER

Clean the breather/cap at the same time that the oil filter is replaced. Use cleaning solvent and
blow dry with clean, dry compressed air.

Figure 3-15: Hydraulic Tank

C A U T I O N

The hydraulic oil may be of sufficient temperature to cause burns. Wear
safety gloves and safety glasses when handling hot oil.

060571-005

Содержание X Series





































































































































































Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды

Upright X Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды