Upright X Series Скачать руководство пользователя страница 13

Страница: 13 / 164

Page 2-1

X Series Work Platform

ion

PERATION

AND

PECIFICATIONS

WARNING

All personnel shall carefully read, understand and follow all safety rules, operating

instructions, and the Scaffold Industry Association’s MANUAL OF

RESPONSIBILITIES of ANSI A92.6-1999 before operating or performing maintenance

on any UpRight Aerial Work Platform.

Safety Rules

NEVER operate the machine without first surveying the work area for surface hazards such as holes, drop-offs,
bumps and debris.

NEVER operate the machine if all guardrails are not properly in place and secured with all fasteners properly
torqued.

SECURE chain or gate across entrance after mounting the platform.

NEVER use ladders or scaffolding on the platform.

NEVER attach overhanging loads or increase the platform size.

LOOK up, down and around for overhead obstructions and electrical conductors.

DISTRIBUTE all loads evenly on the platform.

NEVER use damaged equipment. (Contact UpRight for instructions. See toll-free phone number on back cover.)

NEVER change operating or safety systems.

INSPECT the machine thoroughly for cracked welds, loose hardware, hydraulic leaks, damaged control cable, loose
wire connections and wheel bolts.

NEVER climb down the elevating assembly with the platform elevated.

NEVER perform service on the machine while the platform is elevated without blocking the elevating assembly.

NEVER recharge batteries near sparks or open flame; batteries that are being charged emit highly explosive hydro-
gen gas.

AFTER USE secure the work platform against unauthorized use by turning the key switch off and removing the key.

NEVER replace any component or part with anything other than original UpRight replacement parts without the
manufacturer’s consent.

NEVER operate the machine within

ten feet of power lines.

THIS MACHINE IS NOT INSULATED.

NEVER elevate the platform or drive

the machine while elevated unless

the machine is on firm, level surface.

NEVER sit, stand or climb on

guardrail or midrail.

060571-005

Содержание X Series





































































































































































Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды

Upright X Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды