Upright X Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 164

background image

Page 2-2

Operation and Specifications

2.1 - Introduction

X Series Work Platform

2.1 I

NTRODUCTION

This manual covers operation of the X Series Self-Propelled Work Platform. This manual must
be stored on the machine at all times.

2.2 P

RE

-O

PERATION

AND

S

AFETY

I

NSPECTION

Carefully read, understand and follow all safety rules, operating instructions, labels, and the Scaf-
fold Industry Association’s MANUAL OF RESPONSIBILITIES. Perform the following steps each
day before use.

1. Open module covers and inspect for damage, oil leaks, or missing parts.

2. Check the level of the hydraulic oil with the platform fully lowered. Open the Left Module and

remove the reservoir cap. Oil should be visible in the filler screen. Add hydraulic fluid if nec-
essary.

3. Check that fluid level in the batteries is correct. (See “Battery Maintenance” on Page 2-11.)

4. Verify that batteries are charged.

5. Check that A.C. extension cord has been disconnected from the charger.

6. Check that all guardrails are in place with all fasteners properly tightened.

7. Check that the slide-out deck extension is secured with the pin.

8. Inspect the machine thoroughly for cracked welds, loose or missing hardware, hydraulic

leaks, damaged control cable, loose wire connections and wheel bolts.

9. Close and secure module covers.

10. Move the machine, if necessary, to an unobstructed area to allow for full elevation.

11. Pull Chassis Emergency Stop Switch to the ON position.

12. Pull Platform Emergency Stop Switch to the ON position.

Figure 2-1: Chassis Controls

13. Turn and hold the Chassis Key

Switch to CHASSIS.

14. Push the Chassis Lift/Lower

Switch to LIFT to elevate the
platform until the Scissor Brace
can be rotated to the vertical
position. Block the elevating
assembly as described on
Page 2-10.

15. Visually inspect the elevating

assembly, lift cylinder, cables
and hoses for cracked welds,
loose hardware, hydraulic leaks,
loose wire connections and
erratic operation. Check for miss-
ing or loose parts.

16. Verify that the depression mech-

anism has deployed into position under each module. Remove the Scissor Brace as
described on Page 2-10.

17. Push the Chassis Lift/Lower Switch to LIFT and fully elevate the platform.

18. Partially lower the platform by pushing the Chassis Lift/Lower Switch to LOWER, and check

operation of the audible lowering alarm.

Chassis Key

Switch

Chassis

LIFT/LOWER

Switch

Chassis EMERGENCY

STOP Switch

060571-005

«
...
12
13
14
15
16
...
»

Содержание X Series





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X Series

Бренд: Ultrasonic Страницы: 16

ABICAR 1200 PRO

Бренд: Abicor Binzel Страницы: 64

Бренд: Accutrol Страницы: 25

Бренд: ICP DAS USA Страницы: 4

Бренд: Jacka Industries Страницы: 24

Бренд: Paton Страницы: 31

Бренд: Simplex Страницы: 40

Бренд: Westweld Страницы: 82

Бренд: ATEN Страницы: 176

iAqualink IQ904-P

Бренд: Zodiac Страницы: 2

Бренд: ESAB Страницы: 44

Бренд: Thermal Arc Страницы: 56

Бренд: Paton Страницы: 35

Бренд: Ravaglioli Страницы: 68

SAM GENERATION 2

Бренд: HALE Страницы: 12

INVERTEC CC400-T

Бренд: Lincoln Electric Страницы: 48

JACKSHAFT MOTOR-CONTROL SYSTEM 815-RL

Бренд: Zap Страницы: 28

Бренд: Arc Machines Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды