Upright X Series Скачать руководство пользователя страница 57

Страница: 57 / 164

Page 4-3

Troubleshooting

4.3 - Upright Motor Controller Diagnostics

X Series Work Platform

4.3 U

PRIGHT

OTOR

ONTROLLER

IAGNOSTICS

Batteries must be fully charged before troubleshooting.

Check/Repair all connections before replacing any components

Figure 4-2: Motor Controller

Table 4-1: LED Fault Codes

LASH

ODE

EANING

TATUS

ORRECTIVE

CTION

LED on

Power to the controller and the
controller is operational.

System is functional

None.

LED off

No power to the controller, or
internal fault in the controller.

Battery cables not connected
properly; Failed controller

Check battery cable connections.
Replace the controller.

2 Flash

Procedural fault.

Lift, drive, or steer switch is
engaged at start-up; Drive/Lift
Switch rotated while operating

Cycle the control handle through neutral to clear fault.

3 Flash

Controller senses B- at the M2
terminal.

Short circuit at the motor; M2
cable in contact with B- cable;
Short circuit within controller

Check cable routing and connections.
Test terminals for source of B-.
Replace the controller

4 Flash

Controller senses B+ at the M2
terminal before engaging the
motor start relay.

B+ cable routed incorrectly; M2
cable making contact with B+
cable; Motor start relay
contacts welded closed.

Check cable routing and connections.
Test terminals for source of B+.
Replace the motor start relay.

5 Flash

Controller senses open circuit
at M2 after engaging the motor
start terminal.

Cables loose or not connected;
Faulty motor start relay

Check the cable routing and connections.
Check the signal from motor controller to relay.
Check/replace the motor start relay.

6 Flash

Faulty signal from control
handle or I/O board.

Faulty control handle; Wiring
error

If upper controls are affected, check/replace the control handle.
If lower controls are affected, check/replace the I/O board.

7 Flash

Battery voltage below 12V or
above 45V.

Dead batteries; Bad cable
connections

Check batteries and cable connections.

8 Flash

Thermal cut-off.

Controller is overheated due to
overuse or other failure

Allow system to cool.
Locate and repair other source of overheat.

M2 Terminal

LED Indicator

B- Terminal

060571-005

Содержание X Series





































































































































































Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды

Upright X Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды