Upright X Series Скачать руководство пользователя страница 46

Страница: 46 / 164

Page 3-18

Maintenance

3.15 - Steering Cylinder

X Series Work Platform

NSTALLATION

1. Install the clevis end pivot pin through the cylinder clevis and cylinder link, and secure with a

new cotter pin.

2. Install the rod end shoulder bolt through the cylinder rod and brake tube mounting tabs, and

secure with the locknut.

3. Install the hydraulic hoses.

4. Install the adjustment locknut. Tighten the bolt until the brake shoes fully engage the tires.

Secure with the locknut.

5. Lower the machine and operate the drive circuit. Check that the brake shoes retract and

clear the tires when driving and fully engage the tires when stopped. Test the brakes, if pos-
sible, on a 14° (25%) incline. Check for leaks.

3.15 S

TEERING

YLINDER

EMOVAL

1. Turn the wheels to the straight position.

2. Elevate the platform and block the elevating assembly with the brace. (See “Supporting Ele-

vating Assembly” on Page 3-4.)

3. Tag and disconnect the hose assemblies from the cylinder fittings, and immediately cap the

openings to prevent foreign material from entering.

4. Remove the cotter pins from the pivot pins.

5. Remove the pivot pins, straight up through the Chassis, while supporting the cylinder.

Remove the cylinder.

Figure 3-22: Steering Cylinder

ISASSEMBLY

1. Remove the set screw that secures the thread

cap on the cylinder barrel.

2. Unscrew the thread cap from the barrel.

3. Withdraw the head cap, piston, and shaft

assembly from the barrel tube.

4. Remove the piston nut, piston, and head cap.

5. Remove the rod wiper, U-cup, O-ring, and

backup ring from the headcap. Discard the
seals.

6. Remove the internal backup rings, O-ring,

and cast iron piston seals from the piston and
discard.

LEANING

AND

NSPECTION

1. Wash all the metal parts in cleaning solvent

and blow dry with filtered compressed air.

2. Inspect all the threaded components for

stripped or damaged threads.

3. Check the inside surface of the cylinder barrel

for scoring or excessive wear.

4. Check the piston and headcap for scoring or excessive wear.

5. Inspect the surface of the shaft for scoring or excessive wear.

1.Clevis Pin
2.Bell Crank Weldment
3.Steering Cylinder
4.Bell Crank Pin

5.Wheel Yoke
6.Steering Link
7.Strip Bearing

060571-005

Содержание X Series





































































































































































Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды

Upright X Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды