Upright X Series Скачать руководство пользователя страница 32

Страница: 32 / 164

Page 3-4

Maintenance

3.5 - Supporting Elevating Assembly

X Series Work Platform

3.5 S

UPPORTING

LEVATING

SSEMBLY

X20N, X20W, X26N

Figure 3-5: Blocking the Elevating Assembly--X20N, X20W, X26N

NSTALLATION

1. Park the work platform on a firm,

level surface.

2. Verify that both Emergency Stop

Switches are ON.

3. Turn the Chassis Key Switch to

CHASSIS.

4. Push the Chassis Lift Switch to

UP, and elevate the platform
approximately 9.5 Ft. (2.9 m).

5. Rotate the Scissor Brace

towards the front, and allow it to
hang vertically over the lower
scissor pivot tube.

6. Push the Chassis Lift Switch to

the DOWN position, and gradu-
ally lower the platform until the brace rests on the lower scissor arm pivot tube.

EMOVAL

1. Push the Chassis Lift Switch to the UP position and gradually raise the platform until the

lower end of the Scissor Brace will clear the lower scissor arm pivot tube.

2. Rotate the Scissor Brace up and over towards the rear so that it rests on the cylinder mount,

stowed position.

3. Push the Chassis Lift Switch to the DOWN position, and completely lower the platform.

4. Turn the Chassis Key Switch to DECK.

W A R N I N G

Never perform service on the work platform in the elevating assembly area while the
platform is elevated without first blocking the elevating assembly.

DO NOT stand in the elevating assembly area while deploying or storing the brace.

060571-005

Содержание X Series





































































































































































Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды

Upright X Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды