Upright X Series Скачать руководство пользователя страница 21

Страница: 21 / 164

Page 2-9

Operation and Specifications

2.4 - Transporting The Work Platform

X Series Work Platform

2.4 T

RANSPORTING

ORK

LATFORM

Figure 2-7: Secure Crane Straps

RANE

Secure straps to Lugs only.Guide the crane straps inside the rails
and outside the chassis.

ORKLIFT

Forklift from the rear of the machine using the forklift pockets pro-
vided. If necessary, the machine may be forklifted from the side
by lifting under the Chassis Modules.

Figure 2-8: Transporting the Work Platform

RUCK

1. Maneuver the work platform into trans-

port position and chock the wheels.
The platform must be in the fully low-
ered position for transport.

2. Secure the work platform to the trans-

port vehicle by attaching chains or
straps of adequate load capacity to the
front and rear Tie Downs.

W A R N I N G

Forklifting is for transporting only.

See specifications for weight of the work platform and be certain that forklift
is of adequate capacity to lift the platform.

Rear Tie Down/Lift Lugs

Front Tie Down Lugs

Lift Lugs

REAR

Forklift Pockets

FRONT

C A U T I O N

Front tie down lugs are not to be used to lift the work platform.

Overtightening of chains or straps attached to tie down lugs may result in
damage to the work platform.

060571-005

Содержание X Series





































































































































































Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды

Upright X Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды