44
QUESTIONS AND ANSWER CONCERNING THE USE OF THE BREADMAKER
The bread sticks in the pan after baking
Allow the bread to cool off for approx. 10 minutes. Stand
the pan on its head - if appropriate, lightly waggle the
blade (kneader connection) at the underside of the bread
pan. Before placing the kneading blade, fill the hole in
it with heat-resisting margarine (full-fat), this avoids, that
dough may penetrate between kneading blade and shaft
and may bake there. Before baking is commenced, rub a
little oil on the kneaders.
If you intend to make jam in the breadmaker we recom-
mend to buy a second bread pan exclusively for making
jam, as bread may stick in the pan of jam has been pre-
pared in the same one before.
How can the holes in the bread from the kneader be avoided?
Before the last raising phase, you can remove the kneader
with floured fingers (see the timing of the program process
on the display.
Should you not wish to do that, after baking use the hooked
skewer. If care is taken, larger holes are avoidable.
The dough flows over the bread pan
This may happen, when wheat flour is used, as wheat con-
tains more gluten and thus rises more. In this case
reduce the flour amount and adapt the other ingredients.
The bread will nevertheless have the desired volume.
add 1 tablespoon of liquid butter or margarine.
The bread rises, but sinks in the baking phase
If a “V”-formed channel appears in the bread flour gluten
is missing, that means that the flour contains too little pro-
tein (occurs in rainy summers) or the flour is damp.
Help:
Add to the flour 1 tablespoon of wheat gluten for
every 500 g of flour.
Use a shorter programm, e.g. SCHNELL or ULTRA-
SCHNELL.
If the bread sinks like a funnel in the middle then it could
be that:
the water temperature was too high,
too much water was used.
flour gluten is missing.
When can the Breadmaker lid be opened during the baking
process?
Basically it is always possible when the kneading is taking
place. In this time, one can add small amounts of flour or
liquid when applicable.
If the bread has to have a particular appearance after bak-
ing, take the following steps: before the last raising, care-
fully and shortly open the lid (see the program process
table), make a cut in the crust with a sharp pre-warmed
knife, strew corns on the surface or spread a potato-flour
and water mixture on the crust so that it shines after bak-
ing. This is the last phase in which the BREADMAKER lid
can be opened, otherwise the bread will sink.
What is wholemeal flour?
Wholemeal flour can be made from all sorts of grain, even
wheat. The designation whole meal means that the flour
is ground from the whole grain and thus has more rough-
age. Therefore wheat wholemeal flour is darker. Wholemeal
bread is not necessarily darker as is often assumed.
What has to taken into account when using rye flour?
Rye flour does not contain any binding substances, thus
bread made from it does not rise very much. To make it
edible, a RYE WHOLEMEAL BREAD must be made with
leaven dough.
The dough will only rise when using rye flour that contains
no gluten, if at least ¼ of the amount is replaced by wheat
flour type 550.
What means binding substances in the flour?
The higher the type figure in the above schedule, the lower
the contained binding substances. This means in general
that flours with high type figures do not rise as much as
flour with low type figures. The flour with the highest por-
tion of binding substances is wheat flour of type 550.
Copyright UNOLD AG | www.unold.de
Содержание BACKMEISTER 68010
Страница 6: ...6 EINZELTEILE 6 5 1 7 2 4 3 Copyright UNOLD AG www unold de...
Страница 166: ...166 Copyright UNOLD AG www unold de...
Страница 167: ...167 Copyright UNOLD AG www unold de...
Страница 168: ...Aus dem Hause Copyright UNOLD AG www unold de...
