background image

-2-

•  IMPORTANT: Read this entire manual before installing 

and operating this product. Failure to do so may result 

in property damage, bodily injury, or even death. 

Proper installation of this stove is crucial for safe and 

efficient operation.

• 

Install  vent  at  clearances  specified  by  the  vent 

manufacturer.

• 

If a chimney or creosote fire occurs, press the “OFF” 

button immediately. Do not unplug the unit.

•  Do not connect the pellet vent to a vent serving any 

other appliance or stove.

• 

Do not install a flue damper in the exhaust venting 

system of this unit.

•  Use of outside air is not required for this unit.

• 

Contact  your  local  building  officials  to  obtain  a 

permit and information on any additional installation 

restrictions or inspection requirements in your area.

•  Do not throw this manual away. This manual has 

important operating and maintenance instructions 

that you will need at a later time. Always follow the 

instructions in this manual.

•  This appliance is designed for the use of pelletized 

fuel  that  meet  or  exceed  the  standard  set  by  the 

Pellet Fuel Institute(PFI).

• 

Never  use  gasoline,  gasoline-type  lantern  fuel, 

kerosene,  charcoal  lighter  fluid,  or  similar  liquids  to 

start or ’freshen up’ a fire in this stove. Keep all such 

liquids well away from the stove while it is in use.

•  A working smoke detector must be installed in the 

same room as this product.

•  Do not unplug the stove if you suspect a malfunction. 

Turn the ON/OFF SWITCH to ”OFF’ and contact your 

dealer.

•  Your stove requires periodic maintenance and 

cleaning (see ”MAINTENANCE ”). Failure to maintain 

your stove may lead to improper and/or unsafe 

operation.

•  Disconnect the power cord before performing any 

maintenance! NOTE: Turning the ON/OFF Switch to 

”OFF” does not disconnect all power to the electrical 

components of the stove.

•  Never try to repair or replace any part of the stove 

unless instructions for doing so are given in this 

manual. All other work should be done by a trained 

technician.

•  Do not operate your stove with the viewing door 

open. The auger will not feed pellets under these 

circumstances and a safety concern may arise from 

sparks or fumes entering the room.

•  Allow the stove to cool before performing any 

maintenance or cleaning. Ashes must be disposed in 

a metal container with a tight fitting lid. The closed 

container  of  ashes  should  be  placed  on  a  non-

combustible surface or on the ground, well away 

from all combustible materials, pending final disposal.

• 

The  exhaust  system  should  be  checked  monthly 

during the burning season for any build-up of soot or 

creosote.

•  Do not touch the hot surfaces of the stove. Educate 

all  children  on  the  dangers  of  a  high-temperature 

stove. Young children should be supervised when 

they are in the same room as the stove.

•  The hopper and stove top will be hot during operation; 

therefore, you should always use some type of hand 

protection when refueling your stove.

•  A power surge protector is required. This unit must be 

plugged into a 110 - 120V, 60 Hz grounded electrical 

outlet. Do not use an adapter plug or sever the 

grounding plug. Do not route the electrical cord 

underneath, in front of, or over the heater. Do not 

route the cord in foot traffic areas or pinch the cord 

under furniture.

•  The heater will not operate during a power outage. 

If a power outage does occur, check the heater for 

smoke spillage and open a window if any smoke spills 

into the room.

•  The feed door must be closed and sealed during 

operation.

• 

Never block free airflow through the open vents of 

the unit.

•  Soot and Flyash: Formation and Need for Removal 

– The products of combustion will contain small 

particles of flyash. The flyash will collect in the exhaust 

venting system and restrict the flow of the flue gases. 

Incomplete combustion, such as occurs during 

startup, shutdown, or incorrect operation of the room 

heater will lead to some soot formation which will 

collect  in  the  exhaust  venting  system.  The  exhaust 

venting system should be inspected at least once 

every year to determine if cleaning is necessary.

•  Keep foreign objects out of the hopper.

•  The moving parts of this stove are propelled by high 

torque electric motors. Keep all body parts away from 

the auger while the stove is plugged into an electrical 

outlet. These moving parts may begin to move at any 

time while the stove is plugged in.

• 

Do not place clothing or other flammable items on or 

near this stove.

•  When installed in a mobile home, the stove must be 

grounded directly to the steel chassis and bolted 

to  the  floor.  WARNING—THIS  UNIT  MUST  NOT  BE 

INSTALLED IN THE BEDROOM (per HUD requirements). 

CAUTION—The structural integrity of the mobile home 

floor, wall, and ceiling/roof must be maintained.

•  This appliance is not intended for commercial use.

* This appliance is a freestanding heater. It is not intended to be attached to any type of ducting. It is not a furnace.

Safety Precautions

Содержание KP130















































Отзывы: