Unitech MS842N Скачать руководство пользователя страница 86

Страница: 86 / 132

Enter Setup

Parity Check

A check digit is optional for Standard 25 and can be added as the last digit. It is a calculated value used to verify the

accuracy of the data.

No Parity Check:

The engine transmits Standard 25 barcodes as is.

Do Not Transmit Check Digit After Parity Check:

The engine will run a parity check using the last digit of Standard 25

barcode as check digit. Barcodes passing the check will be transmitted except the last digit, whereas those failing it will not

be transmitted.

Transmit Check Digit After Parity Check:

The engine will run a parity check using the last digit of Standard 25 barcode

as check digit. Barcodes passing the check will be transmitted, whereas those failing it will not be transmitted.

No Parity Check

Do Not Transmit Check Digit After Parity Check

Transmit Check Digit After Parity Check

Exit Setup

Содержание MS842N





































































































































Результаты поиска

Содержание MS842N

Отзывы:

Похожие инструкции для MS842N

Бренды по названию

Популярные бренды

Unitech MS842N, Руководство пользователя

Результаты поиска

Содержание MS842N

Отзывы:

Похожие инструкции для MS842N

Бренды по названию

Популярные бренды