Unitech MS842N Скачать руководство пользователя страница 78

Страница: 78 / 132

Enter Setup

Parity Check

Check digits are optional for Code 93 and can be added as the last two digits, which are calculated values used to verify

the accuracy of the data.

No Parity Check:

The engine transmits Code 93 barcodes as is.

Do Not Transmit Check Digit After Parity Check:

The engine will run parity checks using the last two digits of Code 93

barcode as check digits. Barcodes passing the checks will be transmitted except the last two digits, whereas those failing

them will not be transmitted.

Transmit Check Digit After Parity Check:

The engine will run parity checks using the last two digits of Code 93 barcode

as check digits. Barcodes passing the checks will be transmitted, whereas those failing them will not be transmitted.

No Parity Check

Do Not Transmit Check Digit After Parity Check

Transmit Check Digit After Parity Check

Exit Setup

Содержание MS842N





































































































































Результаты поиска

Содержание MS842N

Отзывы:

Похожие инструкции для MS842N

Бренды по названию

Популярные бренды

Unitech MS842N, Руководство пользователя

Результаты поиска

Содержание MS842N

Отзывы:

Похожие инструкции для MS842N

Бренды по названию

Популярные бренды