Unitech MS842N Скачать руководство пользователя страница 132

Страница: 132 / 132

Appendix 11: Save/Cancel Barcodes

After reading numeric barcode(s), you need to scan the

Save

barcode to save the data. If you scan the wrong digit(s), you

can either scan the

Cancel

barcode and then start the configuration all over again, or scan the

Delete the Last Digit

barcode

and then

the correct digit, or scan the

Delete All digits

barcode and then the digits you want.

For instance, after reading the

Maximum Length

barcode and numeric barcodes “1”, “2” and “3”, you scan:

Delete the Last Digit:

The last digit “3” will be removed.

Delete All Digits:

All digits “123” will be removed.

Cancel:

The maximum length configuration will be cancelled. And the engine is still in the setup mode.

Save

Delete the Last Digit

Delete All Digits

Cancel

Содержание MS842N





































































































































Результаты поиска

Содержание MS842N

Отзывы:

Похожие инструкции для MS842N

Бренды по названию

Популярные бренды

Unitech MS842N, Руководство пользователя

Результаты поиска

Содержание MS842N

Отзывы:

Похожие инструкции для MS842N

Бренды по названию

Популярные бренды