Unitech MS842N Скачать руководство пользователя страница 10

Страница: 10 / 132

Enter Setup

Barcode Scanning

The MS842N feasures fast scanning and decoding accuracy. Barcodes rotated at any angle can still be read with ease.

When scanning a barcode, simply center the aiming beam or pattern projected by the MS842N over the barcode.

Programming Barcodes

Scanning the

Enter Setup

barcode can enable the engine to enter the setup mode. Then you can scan a number of

programming barcodes to configure your engine. To exit the setup mode, scan the

Exit Setup

barcode.

If the engine has exit the setup mode, only some special programming barcodes, such as the

Enter Setup

barcode and

Restore All Factory Defaults

barcode, can be read.

Enter Setup

** Exit Setup

Programming barcode data can be transmitted to the Host. Scan the appropriate barcode below to enable or disable the

transmission of programming barcode data (programming commands) to the Host.

Transmit Programming Barcode Data

** Do Not Transmit Programming Barcode Data

Exit Setup

Содержание MS842N





































































































































Результаты поиска

Содержание MS842N

Отзывы:

Похожие инструкции для MS842N

Бренды по названию

Популярные бренды

Unitech MS842N, Руководство пользователя

Результаты поиска

Содержание MS842N

Отзывы:

Похожие инструкции для MS842N

Бренды по названию

Популярные бренды