Ulvac ULK-04A Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 69

Ulvac ULK-04A Скачать руководство пользователя страница 49

SK00-4802-DI-002-04

No.16.10.20

32

Oil leak check

In the event of oil leakage from the oil filler or drain ports etc., the gasket needs to be replaced
and re-tightened.
The seals used for this unit are available at the nearest service center described at the end of
this document. Please contact the center.

(1) Never scratch the sealing surface with extreme care.

(2) Carefully wipe the sealing surfaces of the flange and the gasket

before assembling clean and dry with alcohol.
Wear clean nylon gloves to avoid touching by bare hands.

(3) After putting the companion flange on, do not move the flange.

(4) A gasket once tightened is not allowed to reuse.

When the flange is removed, replace the gasket with new one.

(5) Be sure to apply molybdenum disulfide before tightening the bolts.

Otherwise the bolts seize up and become unable to be removed.

(6) Do not tighten the tightening bolts to higher than 15 N

･

m.

CAUTION

«
...
47
48
49
50
51
...
»

Содержание ULK-04A






































































Отзывы:

Нет отзывов