Ulvac RFS-1305L Скачать руководство пользователя страница 37

Страница: 37 / 93

RF Power Supply and Matching Box

4. Functions

This chapter describes the functions of each unit.

4-1. RF power supply

The RF power supply can be run locally by the control panel and it can be run remotely by an external

analog signal.

4-1-1.

RF power supply part names and functions

Part names

Description

1. POWER switch

The switch to supply 200 VAC to the RF power supply.
Voltage is supplied to the RF power supply when the switch is in the top
position.
After shutting off the breaker, wait 30 seconds or more before supplying the
power again.

2. AC INPUT connector

Connect the power input cable.

3. RF OUT connector

The connector to output RF power.

4. MB-SIG connector

Connect the matching box with the MB

–

SIG cable.

5. OSC connector

Connect when using external OSC.

6. INTERFACE connector

Wire for external control. When not performing external control,

short pins 1-14.

7. Cooling water IN

The connector for cooling water input. * Not present on 500 W models.

8. Cooling water OUT

The connector for cooling water output. * Not present on 500 W models.

9. GND terminal

Connect to ground.

10. CONTROL connector

Connect the power supply's control panel.

(Unnecessary on 13 MHz 10 kW or higher and 27 MHz systems)

11. RS232C connector

Not used.

Figure 4-1 RF power supply part names

Table 4-1 RF power supply part names and functions

Содержание RFS-1305L






























































































Результаты поиска

Содержание RFS-1305L

Отзывы:

Ulvac RFS-1305L, Инструкция по эксплуатации, Страница: 37 / 93

Результаты поиска

Содержание RFS-1305L

Отзывы: