manualshive.com logo in svg

Travis Industries 2003 ROF, Руководство пользователя

Поделиться
Скачать
Travis Industries 2003 ROF Скачать руководство пользователя страница 4

4

 Safety 

Precautions 

© Travis Industries 

4030407

 100-01146 

 

•  IF YOU SMELL GAS: 

* Shut off gas to the appliance 
* Do not light any appliance 
* Extinguish any open flame 
* Do not touch any electrical switch or plug or unplug anything 
* Call gas supplier, if not reached, call fire department 

 

•  This unit must be installed and repaired by a qualified installer to prevent the 

possibility of an explosion. Your dealer will know the requirements in your area and 
can inform you of those people considered qualified. The Ring of Fire should be 
inspected before use and at least annually by a qualified service person.  More 
frequent cleaning may be required due to excessive debris from leaves, dirt, insects, 
etc. 

•  The instructions in this manual must be strictly adhered to. Do not use makeshift 

methods or compromise in the installation. Improper installation will void the warranty 
and safety listing. 

 

 

• 

This appliance is either approved for natural gas (NG) or for 
propane (LP).  Burning the incorrect fuel will void the warranty 
and safety listing and may cause an extreme safety hazard.  
Direct questions about the type of fuel used to your dealer. 
Check the gas type screw. If the end marked LP is screwed 
into the valve, the end with the red band, it is for LP. The red 
marking is visible with the plastic end cap in place.  

 

Ok

 

• 

Contact your local building 
officials to obtain a permit 
and information on any 
installation restrictions or 
inspection requirements in 
your area.   

 

•  If the flame becomes sooty, 

dark orange in color, or 
extremely tall, do not 
operate the fountain.  Call 
your dealer and arrange for 
proper servicing. 

• 

It is imperative that fountain 
be kept clean and free of 
leaves and debris. This is 
necessary for low 
maintenance and safe 
operation. 

?

 

•  Do not operate the fountain 

if it is not operating properly 
in any fashion or if you are 
uncertain.  Call your dealer 
for a full explanation of your 
fountain and what to expect. 

Gas

 

 

• 

Do not store or use gasoline 
or other flammable liquids in 
the vicinity of this fountain. 

 

 

•  Do not operate if any portion 

of the controls were 
submerged in water or if any 
corrosion occurs. 

•  Do not get the controls wet. 

Be careful not to spray or 
splash water into the control 
area. 

Содержание 2003 ROF

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды