manualshive.com logo in svg

Travis Industries 2003 ROF, Руководство пользователя

Поделиться
Скачать
Travis Industries 2003 ROF Скачать руководство пользователя страница 18

18

 Installation 

 

(for qualified installers only)

 

© Travis Industries 

4030407

 100-01146 

Control Box Connections 

For safety reasons, the control box should be located: 

• 

In a dry location. 

• 

In a place where the fountain can be viewed during operation of the control box.  

• 

4’ Above the ground, away from the reach of small children. 

• 

In plain sight of the fountain, where it is easy accessible in case of emergency. 

 

The control box operates on low voltage. However, electrical codes must be observed in its 

installation.

 

 

• 

Disconnect the electrical supply before installing the control box. 

• 

Find a suitable location to mount the control box.  Attach the mounting base using suitable 
fasteners – 

NOTE

: the control wire can be run through the back or bottom (using the optional 

knock-out) of the mounting base (see the illustration below).   

• 

Uncoil the 25ft roll of 8-conductor cable. Run the end without the connector block through one of 
the holes on the mounting base from the inside. Leave 6” slack for the connector block to connect 
to the control box.  Install the plastic strain relief over the cable and press it into the mounting 
base (this protects the cable).  Connect the connector block on the cable to the blcok on the 
control box. 

• 

Attach the control box to the mounting base – 

NOTE

: the control box is difficult to remove once it 

is installed.  Attach the control cover onto the control box. 

• 

Strip ¼” of the insulation off the wires on the end of the cable.  Attach the included spade 
connectors to the wires (

NOTE

: the light blue wire is not used).  Connect the wires to the terminal 

block of on the fountain (see the illustration below). Note the color-coding on the conductors and 
the markings on the terminal block.  

 

Control Box 

(with cover)

Lig

ht

Wa

ter

Fla

me

Black

Red

White

Yellow

Orange

Brown

Green

Blue

Black

Red

White

Yellow

Orange

Brown

Green

Blue

Remote Control

Terminal Block

Control Box 

Mounting Base

Additional knock-out for 
“Down-the-wall” wire route.

 

Содержание 2003 ROF

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды