manualshive.com logo in svg

Travis Industries 2003 ROF, Руководство пользователя

Поделиться
Скачать
Travis Industries 2003 ROF Скачать руководство пользователя страница 31

 Optional 

Equipment 

(for qualified installers only)

 

31 

Travis Industries 

4030407

 100-01146 

LP Conversion Instructions 

Install the conversion kit prior to installing the gas line to ensure proper gas use. 

NOTE

: 

Remove all 3 screws in the primary air tube when using LP – see page 25. 

1.  Disconnect the pilot line compression fitting at the pilot. Hold the pilot bracket still with a pair of 

pliers and use a ½” wrench to loosen the compression nut. Carefully remove the end of the pilot 
line. The orifice is sitting loosely on the end of the pilot line. If not, give the pilot bracket a light tap 
and the orifice should drop right out. Replace the orifice with the LP orifice, the one with N16 
markings. It usually has a red mark on it. 

2.  Remove the two nuts holding the burner orifice bracket. Drop the bracket and orifice down. 

Change the Natural gas orifice with the LP orifice, the one with a #37 hole. It usually has a red 
mark on it.  Remove the 3 screws in the burner primary air tube (see page 25). 

3.  Remove the plastic cap on the gas type conversion screw on the gas control valve. Unscrew the 

conversion screw. Rotate the screw 180 degrees and screw it back into the valve. The end with 
LPG markings (the side with the red stripe) is screwed into the valve. Replace the plastic cap. 
The red strip on the conversion screw is now visible. 

4.  Follow the instructions in the manual to make the gas line connection. 

At Back, Under Tub. 

 

At Back, Under Tub. 

Burner Orifice Location 

 

Pilot Location 

Valve Gas Type Conversion 

Screw Location 

 

 

 

 

 

Burner Orifice 

Pilot Orifice 

Valve Conversion Screw 

LP: #37 Drill 

LP:  LP 16 (usually has a red 

mark) 

LP: The side marked LPG (usually 

has a red stripe) 

Natural Gas: 3/16” Drill 

Natural Gas: N 26 

Natural Gas: The side mark NAT 

Содержание 2003 ROF

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды