manualshive.com logo in svg

Travis Industries 2003 ROF, Руководство пользователя

Поделиться
Скачать
Travis Industries 2003 ROF Скачать руководство пользователя страница 16

16

 Installation 

 

(for qualified installers only)

 

© Travis Industries 

4030407

 100-01146 

Water Supply Connection 

1.  Disconnect the electrical supply before proceeding. 

2.  Purchase adequate length of ¼” polyethylene tubing and the required fittings to connect the 

fountain to a suitable cold water supply outlet. The illustration below shows a standard water tap 
with female hose thread connected to the fountain. The fittings provided for this application are: 
One female hose to ½ MPT fitting and One ½ MPT to ¼” poly tube compression fitting. 

3.  Remove the compression nut on the fountain float valve (this is the water inlet). Insert the poly 

tubing through the compression nut, ferrule, and seat (included with the Ring of Fire - see the 
illustration below).  Insert the tubing into the water inlet and hand-tighten the compression nut. 

Do 

not over tighten the compression nut

. 

4.  Assemble the water tap fittings and connect the free end of the poly tubing to the fittings. Connect 

the fittings to the water tap. 

5.  Turn on the water tap before operating the fountain and check for water leaks. The fountain is 

equipped with a low water level sensor. It will not operate without being filled with water. The float 
valve located inside the fountain regulates water level in the fountain.  

 

 

 

COLD WATER 

SUPPLY TAP 

FOUNTAIN 

FLOAT VALVE

 

1/2”

Ferrule

Seat

To 
Water 
Supply

To Ring 
of Fire 
Water 
Inlet

Compression 
Nut

 

 

Содержание 2003 ROF

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды