manualshive.com logo in svg

Travis Industries 2003 ROF, Руководство пользователя

Поделиться
Скачать
Travis Industries 2003 ROF Скачать руководство пользователя страница 29

 Safety 

Label 

29 

Travis Industries 

4030407

 100-01146 

The safety (listing) label is adhered to the base of the fountain near the gas control valve.  A copy of 
the safety label is shown below.   

Ring of Fire

Outdoor Gas Fireplace

Serial Number

Report No. 028-G-52-5

Tested to the requirements of CSA 4.96 U.S., (2nd Ed.), I.A.S. Requirements
FOR OUTDOOR USE ONLY
Equipped for use with Natural Gas. For conversion to LP, use kit provided by the manufacturer.
See Manual For Installation on Combustible Floors.

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause
injury or property damage. Refer to the owner's information manual provided with this
appliance. For assistance or additional information consult a qualified installer, service agency
or the gas supplier.

LP

NG

Input Rate (BTU/Hr)

69,000

89,000

Maximum Inlet Pressure (Inches W.C.)

13

7

Manifold Pressure on "HI" (Inches W.C.)

11

3.5

Main Burner Orifice (DMS)

#37

3/16"

See manual for clearances when locating this appliance under overhead unprotected combustible
surfaces.

Clearance to Combustibles:

 A 6-foot

vertical clearance extending up to 3-feet
horizontal from the top finished edge of the
unit. A clearance extending above the line
created from connecting the edge of the unit
to a point 3-feet horizontal from the edge and
3-feet vertical.

If unit is supplied with a self-contained
LP-gas supply system:

CAUTION:

 The gas pressure regulator

provided with this appliance must be used.
This regulator is set for an outlet pressure of
11 Inches water column when converted for
use with LP.

The gas supply must be turned off at the LP-
gas supply cylinder when this appliance is
not in use.

Do not store spare LP gas cylinders under or
near this appliance and never fill a cylinder
beyond 80% full or a fire causing death or
serious injury may occur.

FOR YOUR SAFETY

 - Do not store or

use gasoline or other flammable vapors and
liquids in the vicinity of this or any other
appliance.

WARNING:

 If you do not follow these

instructions exactly, a fire or explosion may
result causing property damage, personal
injury or loss of life.

FOR YOUR SAFETY IF YOU SMELL GAS

– Shut off gas to the appliance.
– Do not try to light any appliance.
– Extinguish any open flame.
– Do not touch any electrical switch.
– Immediately call gas supplier. Follow the

gas supplier's instructions.

– If you cannot reach your gas supplier, call

the fire department.

0488   (IGN)

Jan

2002

May

Sep

Feb

2003

Jun

Oct

Mar

2004

Jul

Nov

Apr

2005

Aug

Dec

Date of Manufacture

10850 117th Pl. NE
Kirkland, WA 98033

6'

3'

3'

 

 

Содержание 2003 ROF

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды