Trane Tracer CH.530 RLC-SVU01B-E4 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 60

background image

398

RLC-SVU01B-E4

28

Diagnostics

NonLatch

The BAS was setup as
"installed" at the MP and the
Comm 3 LLID lost
communications with the BAS
for 15 contiguous minutes after
it had been established. Refer
to Section on Setpoint
Arbitration to determine how
setpoints and operating modes
may be effected by the comm
loss. The chiller follows the
value of the Tracer Default Run
Command which can be
previously written by Tracer
and stored nonvolatilely by the
MP (either use local or
shutdown)

Reset
Level

BAS Communication
Lost

Hex
Code

Persistence

Special

Severity

The following Diagnostic Table
contains all diagnostics possible
arranged alphabetically by the name
assigned to each diagnostic. Not all
diagnostics are available unless
TechView is installed.

Legend to Diagnostics Table

Hex Code:

3-digit code used to

uniquely identify diagnostics.

Diagnostic Name:

Name of the

diagnostic as it appears at DynaView
and/or TechView displays.

Severity:

Defines the action of the

above effect.

Immediate means an

instantaneous shutdown of the
affected portion.

Normal means

routine or friendly shutdown of the
affected portion.

Special Mode

means a particular mode of
operation is invoked, but without
shutdown, and

Info means an

Informational Note or Warning is
generated.

Persistence:

Defines whether or not

the diagnostic and its effects are to
be manually reset (Latched), or can
be either manually or automatically
reset (Nonlatched).

Criteria:

Quantitatively defines the

criteria used in generating the
diagnostic and, if nonlatching, the
criteria for auto reset.

Reset Level:

Defines the lowest level

of manual diagnostic reset
command which can clear the
diagnostic. The manual diagnostic
reset levels in decreasing order of
priority are: Local, Remote and Info.
For example, a diagnostic that has a
reset level of Remote, can be reset
by either a remote diagnostic reset
command or by a local diagnostic
reset command, but not by the
lower priority Info Reset command.

Table 9 - Diagnostics

Diagnostic Name and
Source

Criteria

Remote

«
...
26
27
28
29
30
...
»

Содержание Tracer CH.530 RLC-SVU01B-E4





























































Отзывы:

Нет отзывов

Похожие инструкции для Tracer CH.530 RLC-SVU01B-E4

Бренд: FAAC Страницы: 64

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 4

Бренд: Hach Страницы: 2

Бренд: Hach Страницы: 12

Бренд: Hach Страницы: 472

Бренд: Hach Страницы: 64

Бренд: Hach Страницы: 210

Бренд: Icar Страницы: 40

Бренд: Icar Страницы: 86

Бренд: Icar Страницы: 39

Бренд: TANDBERG Страницы: 2

6000 MXP Profile

Бренд: TANDBERG Страницы: 2

3000 MXP Profile

Бренд: TANDBERG Страницы: 2

Бренд: TANDBERG Страницы: 11

Media Processing System MPS 800

Бренд: TANDBERG Страницы: 106

Бренд: TANDBERG Страницы: 44

Бренд: TANDBERG Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды