Trane CAUJ-C20, Инструкция по установке, эксплуатации и обслуживанию, Страница: 6 / 60

6 CAUJ-SVX01E-EN
General Information
Unit Inspection
As soon as the unit arrives at the job site:
• Verify that the nameplate data matches the data on
the sales order and bill of lading (including
electrical data).
• Verify that the power supply complies with the unit
nameplate specifications.
• Visually inspect the exterior of the unit, including
the roof, for signs of shipping damage.
• Check for material shortages. See the Component
Layout and Ship-With Location illustration.
IIm mp po orrtta an ntt:: If the job site inspection of the unit
reveals damage or material shortages,
ffiille
e a a cclla aiim m w wiitth h tth he e c ca arrrriie err
iim mm me ed diia atte elly y.. S Sp pe ecciiffy y tth he e tty yp pe e a an nd d
e ex xtte en ntt o off tth he e d da am ma ag ge e o on n tth he e ‘‘b biillll o off
lla ad diin ng g” ” b be effo orre e ssiig gn niin ng g..
• Visually inspect the internal components for
shipping damage as soon as possible after delivery
and before it is stored. Do not walk on the sheet
metal base pans.
W WA AR RN NIIN NG G
N No o S Stte ep p S Su urrffa ac ce e!!
F Fa aiillu urre e tto o ffo ollllo ow w iin nssttrru uccttiio on n b be ello ow w cco ou ulld d rre essu ulltt iin n
d de ea atth h o orr sse erriio ou uss iin njju urry y..
D Do o n no ott w wa allkk o on n tth he e s sh he ee ett m me etta all d drra aiin n p pa an n.. W Wa allkkiin ng g
o on n tth he e d drra aiin n p pa an n c co ou ulld d c ca au usse e tth he e ssu up pp po orrttiin ng g m me etta all
tto o cco olllla ap psse e a an nd d rre essu ulltt iin n tth he e o op pe erra atto orr//tte ecch hn niicciia an n
ffa alllliin ng g..
Bridging between the unit's main supports may consist
of multiple 2 by 12 boards or sheet metal grating.
• If concealed damage is discovered, notify the
carrier's terminal of damage immediately by phone
and by mail. Concealed damage must be reported
within 15 days.
• Request an immediate joint inspection of the
damage by the carrier and the consignee. Do not
remove damaged material from the receiving
location. Take photos of the damage, if possible.
The owner must provide reasonable evidence that
the damage did not occur after delivery.
• Notify the appropriate Trane office before installing
or repairing a damaged unit.
Nameplates
Unit Nameplate
One Mylar unit nameplate is located on the outside
upper right corner of the control panel door. It includes
the unit model number, serial number, electrical
characteristics, weight, refrigerant charge, as well as
other pertinent unit data. A small metal nameplate with
model number, serial number, and unit weight is
located just above the Mylar nameplate, and a third
nameplate is located on the inside of the control panel
door.
When ordering replacement parts or requesting
service, be sure to refer to the specific model number,
serial number, and DL number (if applicable) stamped
on the unit nameplate.
Unit Description
All air cooled condensing units are designed for
outdoor installations with vertical air discharge. These
units may be installed on a flat roof or placed on a
concrete slab at ground level.
Before shipment, each unit is leak-tested, evacuated, a
nitrogen holding charge is added, and the controls are
tested for proper operation.
The condenser coils are all-aluminum microchannel
design. Corrosion protected condenser coils are a
standard option. Louvered condenser grilles for coil
protection are standard. Direct-drive, vertical discharge
condenser fans are provided with built-in current and
overload protection.
For “Ship with” items, see the following figures.
If low ambient operation is required, low ambient
dampers are available as a field or factory installed
option.
The unit control panel contains all required fan cycling
controls, compressor interlocks, and a 115 volt control
power transformer. Field wiring, electrical schematics
and panel connection diagrams are located inside the
control panel access door.