Trane CAUJ-C20, Инструкция по установке, эксплуатации и обслуживанию

Страница: 31 / 60

CAUJ-SVX01E-EN 31
Spring Isolators (20 to 120 Ton units)
Figure 22. Spring isolators
5/8”
(15 mm)
2 3/4”
(69 mm)
4 3/4”
(122 mm)
6 1/2”
(165 mm)
7 1/2”
(190 mm)
5/8”
(15 mm)
2 3/4”
(69 mm)
7 3/4”
(198 mm)
9 1/4”
(234 mm)
10 1/4”
(259 mm)
1/2” x 5/8” lg
(13mm x 16mm)
Lev eling Bolt
1/4” to 1/2” Clear ance
5 5/8” (142 mm)
Oper ating Height
5/8” (15 mm)
CP-1
Acoustical Non- Skid
Neoprene P a d
1/2” x 5/8” lg
(13mm x 16mm)
Lev eling Bolt
1/4” to 1/2” Clear ance
6” (152 mm)
Oper ating Height
5/8” (15 mm)
CP-2
Acoustical Non- Skid
Neoprene P a d
Table 8. CAUJ spring isolator selection
Unit Size
(tons)
Mounting Location
1 2 3 4 5 6 7 8
20 CP-1D-340 CP-1D-510 CP-1D-510 CP-1D-340 - - - -
25 CP-1D-510 CP-1D-340 CP-1D-340 CP-1D-340 - - - -
30 CP-1D-510 CP-1D-340 CP-1D-340 CP-1D-340 - - - -
40 CP-1D-510 CP-1D-340 CP-1D-340 CP-1D-510 CP-1D-510 CP-1D-340 - -
50 CP-1D-340 CP-1D-340 CP-1D-510 CP-1D-340 CP-1D-510 CP-1D-510 - -
60 CP-1D-340 CP-1D-340 CP-1D-510 CP-1D-510 CP-1D-510 CP-1D-510 - -
80 CP-1D-675 CP-1D-510 CP-1D-510 CP-1D-340 CP-1D-510 CP-1D-340 CP-1D-675 CP-1D-510
100 CP-1D-675 CP-1D-510 CP-1D-675 CP-1D-510 CP-1D-675 CP-1D-510 CP-1D-675 CP-1D-510
120 CP-1D-900 CP-1D-510 CP-1D-675 CP-1D-510 CP-1D-675 CP-1D-510 CP-1D-675 CP-1D-510
W WA AR RN NIIN NG G
H He ea av vy y O Ob bjje ec ctt!!
F Fa aiillu urre e tto o ffo ollllo ow w iin nssttrru uccttiio on ns s cco ou ulld d rre essu ulltt iin n d de ea atth h
o orr sse erriio ou us s iin njju urry y..
U Usse e sso olliid d tty yp pe e b bllo occkkss,, ii..e e.. 4 4"" X X 4 4"" w wo oo od d b bllo occk kss o orr
s siim miilla arr m ma atte erriia all,, tto o p prre ev ve en ntt cco olllla ap pssiin ng g.. K Ke ee ep p
h ha an nd dss a an nd d o otth he err b bo od dy y lliim mb bss cclle ea arr o off e elle ev va atte ed d b ba as se e
rra aiill w wh hiille e iin nsstta alllliin ng g iis so olla atto orrss..
Install the spring isolators at each unit mounting (load)
point, using the following procedure:
1. Elevate the unit (one side at a time) to allow access
to the base rail mounting holes.
2. Align the mounting holes in the base rail of the unit
with the positioning pin in the top of the
appropriate isolator.
3. Position the isolator to allow access to the
mounting holes in the base of the isolator.
4. Lower the unit onto the isolator. The positioning pin
on the isolator must engage into the hole of the
base rail. The clearance between the upper and
lower isolator housings should be approximately 1/
4 to 1/2 inch. A clearance greater than 1/2 inch
IIn nsstta alllla attiio on n M Me ec ch ha an niic ca all