background image

Tradedor TD77DM & TD77SEL Installation Guide

IMPORTANT SAFETY 

INSTRUCTIONS

The RD77 Econ must be installed 
and operated in accordance with the 
instructions supplied; failure to do so 
could result in damage to your door  
and compromise your safety.

WARNING AND GUIDANCE NOTES

At least TWO people are required to install this product.

Prior to installing please remove all rings, watches and 
sharp objects to avoid any possibility of damage.

Prior to installing please remove any items of loose 
clothing to avoid any risk of entanglement or injury.

Your door comes complete with a 3 pin plug as standard 

(this is supplied and must be fitted with a 13amp fuse) 

which should be plugged straight into a 13amp 3 pin 
switched socket in the vicinity of your door, should you 
need any extra electrical work. This must be carried out 

by a suitably qualified person, if you have any doubts 

please consult an electrician.

Your receiver box should be installed in a location that is 
at a comfortable height to operate the push buttons, but 
out of the easy reach of children.

Please do not allow children to operate the push buttons or 
remote control fobs, as serious injury can occur from misuse.

Warning: you must have a clear line of sight of the whole 
of your roller garage door when the door is in operation. 
Failure to do so may result in harm to persons or damage 
to your roller garage door.

These fitting instructions are for guidance only, you should always assess your garage construction 
for installation as each garage & opening has its own specific needs. Please read these instructions 
carefully and in full before commencing the installation of the roller garage door.

3

Warning & Guidance

Содержание TD77DM













































Отзывы: