manualshive.com logo in svg

FAAC 760, Руководство по установке, Страница: 1 / 31

Поделиться
Скачать
FAAC 760 Скачать руководство пользователя страница 1

The 760 Operator and
450 MPS Control Panel:
Installation Manual

Contents

Important Safety Information ............................................................ 2
Technical Data ............................................................................... 4
The 760 Operator............................................................................ 4
The Control Panel........................................................................... 4
Unpacking the Operator ................................................................... 5
The 760 Swing Gate Operator ........................................................... 6
General Characteristics .................................................................... 6
450 MPS Logic Modes .................................................................... 6
Installation Instructions.................................................................... 9
Preparing the Gate .......................................................................... 9
Manual Release.............................................................................10
Installing the 760 Operator ..............................................................10
Install the Load Bearing Box............................................................10
Secure the Load Bearing Box...........................................................11
Install the Gate Leaf Shoe................................................................11
Install the Gate Leaf .......................................................................14
Install the Operator in  the Load Bearing Box......................................14
Install the 450 MPS Control Panel ....................................................16
Connect the Main Power Supply……………………………………..16
Connect the Operator(s) to the Control Panel………………………..17
Check the Motor's Direction of Rotation……………………………..19
Connect Other Devices……………………………………………….19
Set Operating Controls………………………………………………..21
Fine-tune the Bypass  Valve Pressures ...............................................22
Adjust the Beginning of  the Braking Phase ........................................23
Adjust the Braking Intensity ............................................................23
Assemble and Install  the Manual Release ..........................................23
Installing an Extension Arm.............................................................25
Maintenance .................................................................................26
The 760 Operator...........................................................................26
The Control Panel..........................................................................26
Troubleshooting ............................................................................27
Exploded View, 760 Splined Shaft....................................................28
Exploded View, 760 CBAC-SB-SBS.................................................29
Exploded View, 760 CR..................................................................30

Содержание 760
































Отзывы:

Нет отзывов