![background image](http://html1.mh-extra.com/html/faac/760/760_installation-manual_3110077027.webp)
27
Troubleshooting
WARNING!
Before you do any work on the control panel, be sure to turn off
the main power.
Problem: The gate does not respond to an activating
signal.
Solution:
Verify that you have correctly wired the operator to the
control panel.
Verify that the LED DL3 is on. If it is not illuminated,
then check the fuses on your control panel.
If the LED DL3 is not illuminated and your fuses are
okay, then the stopping device is being triggered and is
preventing the gate from responding to your signal. If
you have no stopping device installed, then be sure you
have installed a jumper across the appropriate terminals.
Verify that your activating device works properly. Either
DL1 or DL2 (depending on your gate design) should
illuminate when you signal the gate to close (or open)
and LED DL3 should be on. If either DL1 or DL2 does
not illuminate when you signal the gate, then the
problem may be in your activating device. Short across
the appropriate terminals. If the short causes the gate to
close (or open), then the problem is in the activating
device. Repair or replace the device.
Problem: The radio controlled opener does not open
the gate.
Solution:
Check the light on the front of the remote transmitter. It
should illuminate when you signal the gate. If it does not
illuminate and if the batteries are okay, repair or replace
the transmitter.
Verify that the wiring is correct for the radio controlled
device and the antenna.
Check DL1 and DL2. One should illuminate when the
transmitter button is pressed.
Determine if the fault is in the receiver by temporarily
connecting a push button device across the appropriate
terminals. If such a push button device opens the gate,
repair or replace the receiver.
Problem: The gate doesn't open (or close) though the
motors are running.
Solution:
Make sure that the motor is running in the right direc-
tion, and make sure the Manual Release mechanism has
fully engaged the hydraulic system.
Increase the bypass pressure in small
1
/
4
turn increments
to see if the hydraulic system needs more pressure.
Problem: The gate opens but does not close.
Solution:
Make sure you have selected the desired operating
mode.
Verify that the reversing devices are working properly.
DL4 or DL5 should illuminate when a reversing device
is triggered. If either does not illuminate, then one of
your reversing devices is preventing the gate from re-
sponding to your signal. Check your reversing devices.
If no reversing devices are installed, make sure a circuit
is installed between appropriate terminals.
If the motor is running, insure that the bypass valves are
correctly adjusted. Increase the bypass pressure in small
1
/
4
turn increments to see if the hydraulic system needs
more pressure.
Problem: The gate does not fully open (or close).
Solution:
Increase the bypass pressure(s) to see if the hydraulic
system needs more pressure.
Check the operator's motor run time selection. You
should set a time that is just longer than the rated speed
of your model of operator. For example, because the 760
CBAC has a rated opening time of 17 sec, you should
select a time that is just longer than the opening time.
Check to see that there are no obstructions in the path of
the gate or that the hinges are not binding.
Problem: The operator doesn't work smoothly and
the gate jerks as it opens and closes.
Solution:
Check the oil level in the operator.
Make sure the Manual Release mechanism has fully
engaged the hydraulic operation of the operator.
Bleed the air from the hydraulic system by cycling the
gate (opening and then closing) 10 times and pausing for
a couple of minutes between cycles.
Make sure that a flexible gate leaf is not the problem. If
the gate leaf flexes, then stiffen the gate or use a slower
operator.
Содержание 760
Страница 20: ...20 Figure 22 Common accessories wired to 450 MPS...
Страница 28: ......
Страница 29: ...UL strain relief kit 2167A 710914 710915 709020002 703930...
Страница 30: ......