![background image](http://html1.mh-extra.com/html/faac/760/760_installation-manual_3110077002.webp)
2
Important Safety Information
Both the installer and the owner and/or operator of
this system need to read and understand this
installation manual and the safety instructions
supplied with other components of the gate system.
This information should be retained by the owner
and/or operator of the gate.
WARNING!
To reduce the risk of injury or death
1 .
R E A D A N D F O L L O W A L L
I N S T R U C T I O N S .
2.
Never let children operate or play with
gate controls. Keep the remote control
away from children.
3.
Always keep people and objects away
from the gate. NO ONE SHOULD
CROSS THE PATH OF THE
MOVING GATE.
4.
Test the gate operator monthly. The
gate MUST reverse on contact with a
rigid object or stop when an object
activates the non-contact sensors. After
adjusting the force or the limit of travel,
retest the gate operator. Failure to
adjust and retest the gate operator
properly can increase the risk of injury
or death.
5.
Use the emergency release only when
the gate is not moving.
6.
KEEP GATES PROPERLY
MAINTAINED. Read the owner’s
manual. Have a qualified service person
make repairs to gate hardware.
7.
The entrance is for vehicles only.
Pedestrians must use separate entrance.
8. SAVE THESE INSTRUCTIONS.
When installing the photo-beams supplied with this unit
two things need to be considered.
1.
Care should be exercised to reduce the risk of
nuisance tripping, such as when a vehicle, trips
the sensor while the gate is in motion.
2.
One or more photobeams shall be located
where the risk of entrapment exists, such as the
perimeter reachable by the moving gate leaf.
Gate Design
1.
A gate is a potential traffic hazard, so it is important
that you locate the gate far enough away from the
road to eliminate the potential of traffic getting
backed up. This distance is affected by the size of
the gate, how often it is used, and how fast the gate
operates.
2.
The operator you choose to install on your gate
must be designed for the type and size of your gate
and for the frequency with which you use the
operator.
3.
Your gate must be properly installed and must work
freely in both directions before the automatic
operator is installed.
4.
An automatic operator should be installed on the
inside of the property/fence line. Do not install the
operator on the public side of the property/fence
line.
5.
Pedestrians should not use a vehicular gate system.
Prevent such inappropriate use by installing
separate gates for pedestrians.
6.
Exposed, reachable pinch points on a gate are
potentially hazardous and must be eliminated or
guarded.
7.
Outward swinging gates with automatic operators
should not open into a public area.
8.
The operating controls for an automatic gate must
be secured to prevent the unauthorized use of those
controls.
9.
The controls for an automatic gate should be
located far enough from the gate so that a user
cannot accidentally touch the gate when operating
the controls.
10.
An automatic gate operator should not be installed
on a gate if people can reach or extend their arms or
legs through the gate. Such gates should be guarded
or screened to prevent such access.
Installation
1.
If you have any question about the safety of the
gate operating system, do not install this operator.
Consult the operator manufacturer.
2.
The condition of the gate structure itself directly
affects the reliability and safety of the gate
operator.
3.
Only qualified personnel should install this
equipment. Failure to meet this requirement could
cause severe injury and/or death, for which the
manufacturer cannot be held responsible.
Содержание 760
Страница 20: ...20 Figure 22 Common accessories wired to 450 MPS...
Страница 28: ......
Страница 29: ...UL strain relief kit 2167A 710914 710915 709020002 703930...
Страница 30: ......