Toshiba E-studio5530cPRO Скачать руководство пользователя страница 204

Страница: 204 / 324

Printing the Configuration Page

This section describes how to print the Configuration Page.

Press [Printer Features].

Press [Configuration Page] on the [List / Test Print].

The configuration page is printed.

Press the [User Tools/Counter] key.

Interpreting the configuration page

This section describes the Configuration Page.

System Reference

• Unit Number

Displays the serial number assigned to the board by its manufacturer.

• Total Memory

Displays the total amount of memory (SDRAM) installed on the printer.

• Firmware Version

• Printer

Displays the version number of the printer firmware.

• System

Displays the version number of the system firmware.

• Engine

Displays the version number of the printer engine.

• LCDC

Displays the version number of the panel display.

• NIB

5. Printer Features

202

Содержание E-studio5530cPRO





































































































































































































































































































































Результаты поиска

Содержание E-studio5530cPRO

Отзывы:

Toshiba E-studio5530cPRO, Руководство по эксплуатации, Страница: 204 / 324

Результаты поиска

Содержание E-studio5530cPRO

Отзывы: