Toro TimeCutter ZS 4200 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 56

background image

Mower Belt Maintenance

Inspecting the Belts

Service Interval:

Every 25 hours—Check the belts for

wear/cracks.

Check the belts for cracks, frayed edges, burn marks, or any
other damage. Replace damaged belts.

Replacing the Mower Belt

Squealing when the belt is rotating, blades slipping when
cutting grass, frayed belt edges, burn marks, and cracks are
signs of a worn mower belt. Replace the mower belt if any of
these conditions are evident.

1.

Park the machine on a level surface and disengage the
blade control switch.

2.

Move the motion control levers outward to the park
position, stop the engine, remove the key, and wait for
all moving parts to stop before leaving the operating
position.

3.

Set the height-of-cut at the lowest cutting position
[1-1/2 inch (38 mm)].

4.

Using a spring removal tool, (Toro part no. 92-5771),
remove the idler spring from the deck hook to remove
tension on the idler pulley and roll the belt off of the
pulleys (Figure 69 and Figure 70).

WARNING

The spring is under tension when installed
and can cause personal injury.

Be careful when removing the belt.

G014930

1

2

3

3

4

5

1

2

3

3

4

5

6

4

Figure 69

Mower Decks with 2 Blades

1.

Idler pulley

4.

Spring

2.

Mower belt

5.

Engine pulley

3.

Outside pulley

6.

Spring removal too

G014931

1

2

3

3

4

5

6

Figure 70

Mower Decks with 3 Blades

1.

Idler pulley

4.

Spring

2.

Mower belt

5.

Engine pulley

3.

Outside pulley

6.

Spring removal too

5.

Route the new belt around the engine pulley and
mower pulleys (Figure 70).

46

«
...
44
45
46
47
48
...
»

Содержание TimeCutter ZS 4200

























































Отзывы:

Нет отзывов

Похожие инструкции для TimeCutter ZS 4200

Бренд: Sabre Страницы: 9

Бренд: Yard-Man Страницы: 8

Powermaster 11029S

Бренд: Rover Страницы: 1

Бренд: Ransomes Страницы: 81

Greensmaster 3150 04358

Бренд: Toro Страницы: 48

Бренд: Jacobsen Страницы: 104

Бренд: RedMax Страницы: 40

Бренд: Gardeo Страницы: 128

Бренд: Bad Boy Страницы: 34

Бренд: Toro Страницы: 24

Smart Speed 569

Бренд: Troy-Bilt Страницы: 20

GF1800 ROPS Cab

Бренд: Kubota Страницы: 19

Бренд: O-Mac Страницы: 64

Бренд: Poulan Pro Страницы: 48

Бренд: Poulan Pro Страницы: 30

Бренд: Poulan Pro Страницы: 48

Бренд: Poulan Pro Страницы: 60

Бренд: Poulan Pro Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды