Toro TimeCutter ZS 4200 Скачать руководство пользователя страница 8

Страница: 8 / 56

Safety and Instructional
Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential
danger. Replace any decal that is damaged or lost.

93-7009

Warning—don't operate the mower with the deflector up or
removed; keep the deflector in place.

Cutting/dismemberment hazard of hand or foot, mower
blade—stay away from moving parts.

Manufacturer's Mark

Indicates the blade is identified as a part from the original
machine manufacturer.

99-3943

For Models with 50 Inch Decks

Engine

105-7015

For Models with 42 Inch Decks

106-8717

Read the instructions before servicing or performing
maintenance.

Check tire pressure every 25 operating hours.

Grease every 25 operating hours.

Engine

Содержание TimeCutter ZS 4200

























































Результаты поиска

Содержание TimeCutter ZS 4200

Отзывы:

Похожие инструкции для TimeCutter ZS 4200

Бренды по названию

Популярные бренды

Toro TimeCutter ZS 4200, Руководство оператора

Результаты поиска

Содержание TimeCutter ZS 4200

Отзывы:

Похожие инструкции для TimeCutter ZS 4200

Бренды по названию

Популярные бренды