Toro TimeCutter ZS 4200 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 56

background image

Maintenance

Note:

Determine the left and right sides of the machine from the normal operating position.

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the first 8 hours

• Change the engine oil.

Before each use or daily

• Check the safety interlock system.
• Check the engine oil level.
• Clean the air intake screen.
• Check the cutting blades.
• Inspect the grass deflector for damage

After each use

• Clean the mower deck housing.

Every 25 hours

• Grease all lubrication points.
• Check tire pressure.
• Check the belts for wear/cracks.

Every 100 hours

• Service the paper element. (more often in dusty, dirty conditions)
• Change the engine oil. (more often in dusty, dirty conditions)
• Check the spark plug(s).
• Replace the in-line fuel filter

Every 200 hours

• Replace the paper element. (more often in dusty, dirty conditions)
• Change the oil filter. (more often in dusty, dirty conditions)

Before storage

• Charge the battery and disconnect battery cables.
• Perform all maintenance procedures listed above before storage.
• Paint any chipped surfaces.

Important:

Refer to your engine operator's manual for additional maintenance procedures.

CAUTION

If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure
you or other bystanders.

Remove the key from the ignition and disconnect the wire from the spark plug before you do any
maintenance. Set the wire aside so that it does not accidentally contact the spark plug.

30

«
...
28
29
30
31
32
...
»

Содержание TimeCutter ZS 4200

























































Отзывы:

Нет отзывов

Похожие инструкции для TimeCutter ZS 4200

Бренд: Gardol Страницы: 171

Бренд: H&S Страницы: 30

FREEDOM Z SFZ36-17KA

Бренд: Scag Power Equipment Страницы: 69

Бренд: Toro Страницы: 56

Бренд: Racing Страницы: 21

PowerMax 32/18V

Бренд: Gardena Страницы: 182

Бренд: Stihl Страницы: 392

Бренд: Euro garden Страницы: 84

Бренд: GreenWorks Страницы: 31

Бренд: Troy-Bilt Страницы: 48

Бренд: White Outdoor Страницы: 32

Бренд: Cub Cadet Страницы: 64

Бренд: Sabo Страницы: 99

Бренд: Sabo Страницы: 114

Бренд: Peco Страницы: 21

Бренд: Peco Страницы: 26

Бренд: Homelite Страницы: 64

Бренд: Grillo Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды