Toro TimeCutter ZS 4200 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 56

background image

3.

Measure from the tip of the blade to the flat surface
here.

G014973

1

2

3

Figure 53

1.

Blade, in position for measuring

2.

Level surface

3.

Measured distance between blade and surface (A)

4.

Rotate the same blade 180 degrees so that the opposing
cutting edge is now in the same position.

G014974

1

2

3

Figure 54

1.

Blade, side previously measured

2.

Measurement position used previously

3.

Opposing side of blade being moved into measurement
position

5.

Measure from the tip of the blade to the flat surface
here. The variance should be no more than 1/8 inch
(3mm).

G014973

1

2

3

Figure 55

1.

Opposing blade edge, in position for measuring

2.

Level surface

3.

Second measured distance between blade and surface (B)

WARNING

A blade that is bent or damaged could break
apart and could seriously injure or kill you or
bystanders.

•

Always replace bent or damaged blade
with a new blade.

•

Never file or create sharp notches in the
edges or surfaces of blade.

A.

If the difference between A and B is greater
than 1/8 inch (3mm) replace the blade with a
new blade. Refer to Removing the Blades and
Installing the Blades.

Note:

If a bent blade is replaced with a new one

and the dimension obtained continues to exceed
1/8 inch (3mm), the blade spindle could be bent.
Contact an Authorized Toro Dealer for service.

B.

If the variance is within constraints, move to the
next blade..

Repeat this procedure on each blade.

Removing the Blades

The blades must be replaced if a solid object is hit, if the
blade is out of balance, or the blade is bent. To ensure
optimum performance and continued safety conformance
of the machine, use genuine Toro replacement blades.
Replacement blades made by other manufacturers may result
in non-conformance with safety standards.

Hold the blade end using a rag or thickly-padded glove.
Remove the blade bolt, curved washer, blade stiffener, and
blade from the spindle shaft (Figure 56).

41

«
...
39
40
41
42
43
...
»

Содержание TimeCutter ZS 4200

























































Отзывы:

Нет отзывов

Похожие инструкции для TimeCutter ZS 4200

Бренд: Jacobsen Страницы: 114

Бренд: MTD Страницы: 44

Бренд: Lawn-Boy Страницы: 32

Бренд: SIP Страницы: 189

Бренд: Yard-Man Страницы: 16

Бренд: MTD Страницы: 16

Бренд: RedMax Страницы: 40

Бренд: Ozito Страницы: 14

Бренд: Jacobsen Страницы: 92

Бренд: Baroness Страницы: 93

Бренд: MTD Страницы: 32

Бренд: Cramer Страницы: 9

Бренд: Craftsman Страницы: 8

Бренд: Craftsman Страницы: 20

Бренд: Craftsman Страницы: 20

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 12

Бренд: Craftsman Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды