Toro TimeCutter ZS 4200 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 56

background image

Figure 47

1.

Positive battery post

3.

Red (+) charger lead

2.

Negative battery post

4.

Black (-) charger lead

Note:

Do not run the machine with the battery

disconnected, electrical damage may occur.

Installing the Battery

1.

Position the battery in the tray (Figure 46).

2.

Install the positive (red) battery cable to the positive (+)
battery terminal using the fasteners removed previously.

3.

Install the negative battery cable to the negative (-)
battery terminal using the fasteners removed previously.

4.

Slide the red terminal boot onto the positive (red)
battery post.

5.

Secure the battery with the hold-down (Figure 46).

6.

Lower the seat.

Servicing the Fuses

The electrical system is protected by fuses. It requires
no maintenance; however, if a fuse blows, check the
component/circuit for a malfunction or short.

Fuse:

•

Main F1-30 amp, blade-type

•

Charge Circuit F2-25 amp, blade-type

1.

Remove the screws securing the control panel to the
machine. Retain all fasteners

2.

Lift the control pane up to access the main wiring
harness and fuse block (Figure 48).

3.

To replace a fuse, pull out on the fuse to remove it
(Figure 48).

30

25

30

25

G014921

2

1

Figure 48

1.

Main-30 amp

2.

Charge circuit-25 amp

4.

Return the control panel to its original position. Use
the screws removed previously to secure the panel to
the machine.

38

«
...
36
37
38
39
40
...
»

Содержание TimeCutter ZS 4200

























































Отзывы:

Нет отзывов

Похожие инструкции для TimeCutter ZS 4200

Бренд: Sabre Страницы: 9

Бренд: Lawn-Boy Страницы: 24

Бренд: Lawn-Boy Страницы: 84

Бренд: Lawn-Boy Страницы: 20

Бренд: Snapper Страницы: 1

Бренд: ZIPPER MASCHINEN Страницы: 65

Бренд: Snapper Страницы: 28

Бренд: SaMASZ Страницы: 52

Enviromower ENV369B

Бренд: Victa Страницы: 28

Бренд: White Outdoor Страницы: 32

Бренд: Tiger Страницы: 230

Бренд: Cub Cadet Страницы: 44

Rear Blades RB 15

Бренд: Land Pride Страницы: 1

Бренд: Land Pride Страницы: 22

Бренд: Land Pride Страницы: 64

Бренд: Land Pride Страницы: 72

Бренд: Mountfield Страницы: 20

Бренд: Mountfield Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды