Toro TimeCutter ZS 4200 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 56

background image

120-5468

1.

Slow speed

2.

Fast speed

120-2239

1.

Warning—read the

Operator's Manual.

5.

Warning—do not use split ramps, use a full ramps when
transporting machine.

2.

Warning—read the instructions before servicing or performing
maintenance; move the motion control levers to the park
(brake) position, remove the ignition key and disconnect the
spark plug wire.

6.

Loss of traction/control hazard, slopes—loss of traction/control
on a slope, disengage the blade control switch (PTO),
proceed off the slope slowly.

3.

Cutting/dismemberment hazard, mower blade; entanglement
hazard, belt—stay away from moving parts, keep all guards
and shields in place.

7.

Crushing/dismemberment hazard of bystanders, reversing;
crushing/dismemberment hazard of bystanders—do not carry
passengers, look behind and down when reversing.

4.

Thrown object hazard—keep bystanders a safe distance from
the machine, pick up debris before operating, keep deflector
in place.

8.

Tipping hazard—do not mow slopes greater than 15 degrees,
avoid sudden and sharp turns while on slopes.

11

«
...
9
10
11
12
13
...
»

Содержание TimeCutter ZS 4200

























































Отзывы:

Нет отзывов

Похожие инструкции для TimeCutter ZS 4200

Бренд: H&S Страницы: 30

Бренд: Victa Страницы: 20

Бренд: Toro Страницы: 52

Бренд: Windsor Страницы: 60

G - PLEX WD series

Бренд: Ransomes Страницы: 181

Бренд: Redexim Страницы: 12

Бренд: HUSTLER Страницы: 65

Бренд: Yazoo/Kees Страницы: 42

Бренд: Southern States Страницы: 36

Бренд: MTD Страницы: 20

Бренд: Baroness Страницы: 87

PARK 13-6113-56

Бренд: Stiga Страницы: 2

Бренд: Ranger Страницы: 38

Бренд: Stiga Страницы: 64

Бренд: Honda Страницы: 81

RS seriesMS series

Бренд: Robomow Страницы: 4

Бренд: Robomow Страницы: 84

Бренд: Simplicity Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды