Toro Multi Pro 41394 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 96

background image

USB Power Port

The 2-socket USB power port is located at the back
of the armrest.

g194424

Figure 12

1.

USB port

2.

USB sockets

Sprayer Controls

g195515

Figure 13

1.

Application-rate switch

7.

Center-section switch

2.

Pressure gauge

8.

Left-section switch

3.

Spray-mode switch

9.

Master section switch

4.

Tank-agitation switch

10.

Left boom-section lift
switch

5.

Right boom-section lift
switch

11.

Spray-pump switch

6.

Right-section switch

Pressure Gauge

The pressure gauge (

) is located on the

dash. This gauge shows the pressure of the fluid in
the spray system in psi and kPa.

Spray-Mode Switch

Use the spray-mode switch to change between the
application rate mode (closed loop) and the manual
mode (open loop).

Application-Rate Switch

The application-rate switch is located on the dash
to the right of the steering wheel (

). Use

the application-rate switch to control the spray pump
speed when operating the sprayer in the manual
mode. Press and hold the switch forward to increase
the application rate (pressure), or press and hold it
rearward to decrease the application rate (pressure).

18

«
...
16
17
18
19
20
...
»

Содержание Multi Pro 41394

































































































Отзывы:

Нет отзывов

Похожие инструкции для Multi Pro 41394

Бренд: WAGNER Страницы: 55

Бренд: Coleman Страницы: 2

Бренд: ZUPAN Страницы: 34

Бренд: Sanique Страницы: 20

Бренд: Echo Страницы: 60

Бренд: Perel Страницы: 35

Бренд: Graco Страницы: 18

Бренд: Graco Страницы: 32

L2100 Plus 240V

Бренд: ASM Страницы: 20

Бренд: Hardi Страницы: 32

Бренд: Binks Страницы: 17

VIBRA-FLO 17P002

Бренд: Graco Страницы: 12

Бренд: Graco Страницы: 86

Бренд: Kärcher Страницы: 164

Бренд: OHAUS Страницы: 130

Inocoat Inogun M

Бренд: Sames Страницы: 69

Бренд: SAMES KREMLIN Страницы: 31

Бренд: SAMES KREMLIN Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды