Toro Multi Pro 41394 Скачать руководство пользователя страница 79

Страница: 79 / 96

Cleaning the Flow Meter

Service Interval:

Every 200 hours/Yearly (whichever

comes first) (more often when using
wettable powders).

Thoroughly rinse and drain the entire spraying
system.

Remove the flow meter from the sprayer and
flush it with clean water.

Remove the retainer ring on the upstream side
(

Figure 108

g214630

Figure 108

Flange (flow-meter body)

Upstream hub and bearing
(with keyway up)

Downstream hub (with
keyway up)

Turbine stud

Retaining ring

Wire-harness clamp

Downstream arrow
(flow-meter body)

10.

Flange-head screw

Upstream

11.

Sensor assembly

Rotor/magnet

Clean the turbine and the turbine hub to remove
metal filings and any wettable powders.

Inspect the turbine blades for wear.

Note:

Hold the turbine in your hand and spin

it. It should spin freely with little drag. If it does
not, replace it.

Assemble the flow meter.

Use a low pressure (50 kPa or 5 psi) air jet to
ensure that the turbine spins freely.

Note:

If the turbine does not spin freely, loosen

the hex stud on the bottom of the turbine hub by
1/16 of a turn until it does spins freely.

Cleaning the Agitation and
Section Valves

•

To clean the agitation valve; refer to the following
sections:

Removing the Valve Actuator (page 79)

Removing the Agitation-Manifold Valve

(page 80)

Cleaning the Manifold Valve (page 82)

Assembling the Manifold Valve (page 83)

Installing the Agitation-Manifold Valve (page

85)

Installing the Valve Actuator (page 86)

•

To clean the 3 section valves; refer to the following
sections:

Removing the Valve Actuator (page 79)

Removing the Section-Manifold Valve (page

81)

Cleaning the Manifold Valve (page 82)

Assembling the Manifold Valve (page 83)

Installing the Section-Manifold Valve (page

84)

Installing the Valve Actuator (page 86)

Removing the Valve Actuator

Position the sprayer on a level surface, engage
the parking brake, stop the pump, shut off the
engine, and remove the key.

Remove the retainer that secures the actuator
to the manifold valve for the section valve or
agitation valve (

Figure 109

Note:

Squeeze the 2 legs of the retainer

together while pushing it down.

Note:

Retain the actuator and retainer for

installation in

Installing the Valve Actuator (page

86)

Содержание Multi Pro 41394

































































































Результаты поиска

Содержание Multi Pro 41394

Отзывы:

Похожие инструкции для Multi Pro 41394

Бренды по названию

Популярные бренды

Toro Multi Pro 41394, Руководство оператора

Результаты поиска

Содержание Multi Pro 41394

Отзывы:

Похожие инструкции для Multi Pro 41394

Бренды по названию

Популярные бренды