Toro 74901 Z Master 5000 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 68

background image

Figure 81

Adjusting the Motion Control
Linkage

Located on either side of the fuel tank, below the seat are
the pump control linkages. Rotating the pump linkage with a
1/2 inch wrench allows fine tuning adjustments so that the
machine does not move in neutral. Any adjustments should
be made for neutral positioning only.

WARNING

Engine must be running and drive wheels must
be turning so motion control adjustment can be
performed. Contact with moving parts or hot
surfaces may cause personal injury.

Keep fingers, hands, and clothing clear of rotating
components and hot surfaces.

1.

Prior to starting the engine, push the deck lift pedal
and remove the height of cut pin. Lower deck to the
ground.

2.

Raise the rear of machine up and support with jack
stands (or equivalent support) just high enough to
allow drive wheels to turn freely.

3.

Remove the electrical connection from the seat safety
switch, located under the bottom cushion of the seat.
The switch is a part of the seat assembly.

4.

Temporarily

install a jumper wire across the terminals

in the connector of the main wiring harness.

5.

Start engine.

Brake must be engaged and motion

control levers out to start engine. Operator does
not have to be in the seat because of the jumper
wire being used.

Run engine at full throttle and

release brake.

6.

Run the unit at least 5 minutes with the drive levers at
full forward speed to bring hydraulic oil up to operating
temperature.

Note:

The motion control lever needs to be in neutral

while making any necessary adjustments.

7.

Bring the motion control levers into the neutral
position. Adjust pump control rod lengths by rotating
the double nuts on the rod in the appropriate direction
until the wheels slightly creep in reverse (Figure 82).
Move the motion control levers to the reverse position
and while applying slight pressure to the lever allow
the reverse indicator springs to bring the levers back
to neutral. The wheels must stop turning or slightly
creep in reverse.

g014943

Figure 82

1.

Double nuts

8.

Shut off unit. Remove jumper wire from wire harness
and plug connector into seat switch.

9.

Remove the jack stands.

10.

Raise the deck and re-install the height of cut pin.

11.

Check that the machine does not creep in neutral with
the park brakes disengaged.

Adjusting the Motion Control
Damper

The top damper mounting bolt can be adjusted to obtain
a more desired motion control lever resistance. See
Figure 83 for mounting options.

52

«
...
50
51
52
53
54
...
»

Содержание 74901 Z Master 5000





































































Отзывы:

Нет отзывов

Похожие инструкции для 74901 Z Master 5000

Бренд: Yard Machines Страницы: 8

ELM 42/1800 PLUS

Бренд: F.F. Group Страницы: 52

Бренд: Snapper Страницы: 8

Бренд: Poulan Pro Страницы: 56

Бренд: Exmark Страницы: 5

Бренд: Yardworks Страницы: 24

Бренд: Toro Страницы: 28

Бренд: Peco Страницы: 12

Бренд: Toro Страницы: 24

Бренд: Troy-Bilt Страницы: 40

CRAFTSMAN 944.604931

Бренд: Sears Страницы: 56

Craftsman 917.254920

Бренд: Sears Страницы: 29

Бренд: Sears Страницы: 28

Бренд: Sears Страницы: 56

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды