Toro 74901 Z Master 5000 Скачать руководство пользователя страница 17

Страница: 17 / 68

The use of protective equipment for eyes, ears, feet and head
is recommended.

G009027

Figure 10

Wear safety glasses

Wear hearing protection

Operating the Parking Brake

Always set the parking brake when you stop the machine or
leave it unattended.

Setting the Parking Brake

WARNING

Parking brake may not hold machine parked on a
slope and could cause personal injury or property
damage.

Do not park on slopes unless wheels are chocked
or blocked

G016994

Figure 11

Releasing the Parking Brake

G016995

Figure 12

Operating the Mower Blade
Control Switch (PTO)

The blade control switch (PTO) starts and stops the mower
blades and any powered attachments.

Engaging the Blade Control Switch
(PTO)

Note:

Engaging the blade control switch (PTO) with the

throttle position at half or less will cause excessive wear to
the drive belts.

G008945

Figure 13

Disengaging the Blade Control Switch
(PTO)

G009174

Figure 14

Operating the Throttle

The throttle control can be moved between

Fast

and

Slow

positions (Figure 15).

Always use the fast position when turning on the mower deck
with the blade control switch (PTO).

G008946

Figure 15

Содержание 74901 Z Master 5000





































































Результаты поиска

Содержание 74901 Z Master 5000

Отзывы:

Похожие инструкции для 74901 Z Master 5000

Бренды по названию

Популярные бренды

Toro 74901 Z Master 5000, Руководство оператора

Результаты поиска

Содержание 74901 Z Master 5000

Отзывы:

Похожие инструкции для 74901 Z Master 5000

Бренды по названию

Популярные бренды