Toro 74901 Z Master 5000 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 68

background image

G015459

H

3

4

Figure 85

Either dipstick will be used in the machine

1.

Full

3.

H

–means high level

2.

Add

4.

Dipstick locations under
seat

WARNING

Hydraulic oil escaping under pressure can
penetrate skin and cause injury.

•

If hydraulic oil is injected into the skin it
must be surgically removed within a few
hours by a doctor familiar with this type
of injury. Gangrene may result if this is
not done.

•

Keep body and hands away from pin hole
leaks or nozzles that eject high pressure
hydraulic oil.

•

Use cardboard or paper to find hydraulic
leaks.

•

Safely relieve all pressure in the hydraulic
system before performing any work on the
hydraulic system.

•

Make sure all hydraulic oil hoses and lines
are in good condition and all hydraulic
connections and fittings are tight before
applying pressure to hydraulic system.

Replacing the Hydraulic Filters and
Hydraulic Oil

Service Interval:

After the first 250 hours—Change the

hydraulic filters and hydraulic oil when
using any type of oil.

Every 250 hours—Change the hydraulic filters and
hydraulic oil when using Mobil

®

1 oil (more often in

dirty or dusty conditions).

Every 500 hours—Change the hydraulic filters and
hydraulic oil when using Toro

®

HYPR-OIL

™

500

hydraulic oil (more often in dirty or dusty conditions).

To replace the hydraulic oil, the filters need to be removed.
Replace both at the same time. Refer to the oil specifications
under Servicing the Hydraulic System for the correct oil.

1.

Disengage the blade control switch (PTO), move the
motion control levers to the neutral locked position
and set the parking brake.

2.

Stop the engine, remove the key, and wait for all moving
parts to stop before leaving the operating position.

3.

Raise the machine and support it with jack stands
(Figure 86).

Figure 86

1.

Jack stands

4.

Remove both the mower belt and the pump drive belt.
This will prevent oil getting on the belts. Refer to Belts
in the Maintenance Section.

5.

Place a drain pan under the filter, remove the old filter
and wipe the surface clean (Figure 87).

54

«
...
52
53
54
55
56
...
»

Содержание 74901 Z Master 5000





































































Отзывы:

Нет отзывов

Похожие инструкции для 74901 Z Master 5000

Бренд: Toro Страницы: 2

Бренд: Snapper Страницы: 1

Бренд: Yard-Man Страницы: 24

Бренд: Echo Страницы: 244

Бренд: Scag Power Equipment Страницы: 24

67971 - LF 3400

Бренд: Jacobsen Страницы: 122

Бренд: Wards Garden Mark Страницы: 16

Бренд: Yazoo Страницы: 8

Бренд: Lastec Страницы: 23

Бренд: Aerotek Страницы: 18

Бренд: Sabo Страницы: 280

Бренд: Toro Страницы: 28

Бренд: Earthwase Страницы: 20

Бренд: Poulan Pro Страницы: 48

Бренд: Weed Eater Страницы: 30

Бренд: Nakayama Страницы: 80

Flymo Micro Compact 300 Plus

Бренд: Electrolux Страницы: 12

Бренд: Craftsman Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды