Toro 74901 Z Master 5000 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 68

background image

Stopping the Machine

To stop the machine, move the traction control levers to
neutral and move to locked position, disengage the power
take off (blade control switch (PTO), and turn the ignition
key to off.

Set the parking brake when you leave the machine; refer to
Setting the Parking Brake in Operation. Remember to remove
the key from the ignition switch.

CAUTION

Children or bystanders may be injured if they
move or attempt to operate the machine while it is
unattended.

Always remove the ignition key and set the parking
brake when leaving the machine unattended, even
if just for a few minutes.

Adjusting the Height of Cut

Using the Transport Lock

The transport lock has two positions and is used with the
deck lift pedal. There is a lock position and a unlock position
for the transport position. The transport lock is used with the
deck lift pedal. Refer to Figure 26

Figure 26

Transport Lock Positions

1.

Transport lock

3.

Unlock position—does not
lock the mower deck into
transport position

2.

Lock position—mower
deck will lock into transport
position

22

«
...
20
21
22
23
24
...
»

Содержание 74901 Z Master 5000





































































Отзывы:

Нет отзывов

Похожие инструкции для 74901 Z Master 5000

Бренд: Walker Страницы: 100

Бренд: Dixon Страницы: 8

Бренд: Nakayama Страницы: 65

Бренд: TOPMAQ Страницы: 20

CYCLONE MJ31-200

Бренд: Major Страницы: 88

Бренд: Ariens Страницы: 32

Бренд: McCulloch Страницы: 20

Бренд: Murray Страницы: 52

Бренд: Bad Boy Страницы: 34

Бренд: Swisher Страницы: 16

Бренд: Gude Страницы: 92

Бренд: Kobalt Страницы: 24

Бренд: Wheel Horse Страницы: 8

Бренд: Wheel Horse Страницы: 11

REO Royale IV LL-217

Бренд: Wheel Horse Страницы: 12

Бренд: MTD Страницы: 20

Бренд: MTD Страницы: 20

Бренд: MTD Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды