Toro 74901 Z Master 5000 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 68

background image

Check and Clean the Hydraulic
Unit Shrouds

Service Interval:

Before each use or daily

1.

Disengage the PTO and set the parking brake.

2.

Stop the engine, remove the key, and wait for all moving
parts to stop before leaving the operating position.

3.

Raise the seat.

4.

Clean the debris and grass from the hydraulic unit
shrouds (Figure 74).

5.

Lower the seat.

Figure 74

1.

Hydraulic unit shrouds

Brake Maintenance

Adjusting the Parking Brake

Service Interval:

After the first 100 hours

Every 500 hours thereafter

Check to make sure brake is adjusted properly. This procedure
must be followed after the first 100 hours or when a brake
component has been removed or replaced.

1.

Drive the machine onto a level surface.

2.

Disengage the blade control switch (PTO), move the
motion control levers to the neutral locked position
and set the parking brake.

3.

Stop the engine, wait for all moving parts to stop, and
remove the key.

4.

Raise the back of the machine up and support the
machine with jack stands.

DANGER

Mechanical or hydraulic jacks may fail to
support machine and cause a serious injury.

•

Use jack stand when supporting machine.

•

Do not use hydraulic jacks.

5.

Remove the rear tires from the machine.

6.

Remove any debris from the brake area.

7.

Rotate the drive wheel release handle to the

released

position. Refer to the

Using the Drive Wheel

Release Valves

section in Operation.

8.

Measure the overall length of the compression spring.
The correct length should be between 1-1/2 and
1-9/16 inches (3.8 and 4.0 cm). If the spring length is
within this range, no adjustment is needed. If it is not,
proceed to step 9.

9.

Hold the threaded rod end with a tool and adjust
the lock nut until the spring length is between 1-1/2
and 1-9/16 inches (3.8 and 4.0 cm) (Figure 75). Do
Not allow the cable to turn when the nuts are being
loosened.

48

«
...
46
47
48
49
50
...
»

Содержание 74901 Z Master 5000





































































Отзывы:

Нет отзывов

Похожие инструкции для 74901 Z Master 5000

COMPANION 27826

Бренд: COMPANION Страницы: 84

Бренд: Poulan Pro Страницы: 32

Бренд: Toro Страницы: 80

Бренд: Simplicity Страницы: 56

Бренд: Yard-Man Страницы: 12

Бренд: Electrolux Страницы: 13

Бренд: Electrolux Страницы: 16

6Speed - 96012008900 42" 16.5HP Riding Mower

Бренд: Electrolux Страницы: 36

Бренд: Electrolux Страницы: 8

Бренд: Electrolux Страницы: 10

Бренд: Electrolux Страницы: 40

Bestgreen BM135H107

Бренд: Electrolux Страницы: 52

Бренд: Electrolux Страницы: 40

Бренд: Electrolux Страницы: 76

Бренд: Electrolux Страницы: 56

Бренд: Electrolux Страницы: 88

Flymo Compact 300

Бренд: Electrolux Страницы: 11

Бренд: MTD Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды