Toro 74901 Z Master 5000 Скачать руководство пользователя страница 63

Страница: 63 / 68

Stop the engine, allow it to cool, and drain the
fuel tank; refer to Servicing the Fuel Tank in the
Maintenance Section.

Restart the engine and run it until it stops.

Dispose of fuel properly. Recycle as per local
codes.

Important:

Do not store

stabilizer/conditioned fuel over 90 days.

13.

Check and tighten all bolts, nuts, and screws. Repair or
replace any part that is damaged.

14.

Paint all scratched or bare metal surfaces. Paint is
available from your Authorized Service Dealer.

15.

Store the machine in a clean, dry garage or storage area.
Remove the key from the ignition switch and keep it
out of reach of children or other unauthorized users.
Cover the machine to protect it and keep it clean.

Содержание 74901 Z Master 5000





































































Результаты поиска

Содержание 74901 Z Master 5000

Отзывы:

Похожие инструкции для 74901 Z Master 5000

Бренды по названию

Популярные бренды

Toro 74901 Z Master 5000, Руководство оператора

Результаты поиска

Содержание 74901 Z Master 5000

Отзывы:

Похожие инструкции для 74901 Z Master 5000

Бренды по названию

Популярные бренды