Toro 08781 Скачать руководство пользователя страница 17

3.

Insert the new dipstick and check the level of
the hydraulic fluid (

Figure 37

).

4.

Slowly add the additional fluid to bring it to the

Full

mark.

g003618

Figure 37

1.

Hydraulic-tank cap

3.

Hydraulic tank

2.

Dipstick

5.

Start the machine and let it run for 5 minutes.

6.

Check for any leaks in the system with a piece
of cardboard.

WARNING

Hydraulic fluid escaping under pressure
can penetrate skin and cause injury.

If hydraulic fluid is injected into the skin
it must be surgically removed within a
few hours by a doctor familiar with this
type of injury. Gangrene may result if
this is not done.

Keep body and hands away from
pin-hole leaks or nozzles that eject
high-pressure hydraulic fluid.

Use cardboard or paper to find
hydraulic leaks.

Safely relieve all pressure in the
hydraulic system before performing
any work on the hydraulic system.

Make sure that all hydraulic-fluid
hoses and lines are in good condition
and that all hydraulic connections
and fittings are tight before applying
pressure to the hydraulic system.

7.

Install the left front screen to the frame.

8.

Install the front shroud to the frame with 4
flange-head screws.

9.

Install the 4 flange-head screws securing the left
wheel shroud to the frame (

Figure 38

).

10.

Install the left rear tire (

Figure 38

).

g003581

Figure 38

1.

Left wheel shroud

3.

Left tire

2.

Flange-head screws

4.

Nut

11.

Lower the machine onto the ground.

12.

Install the rear hitch shield.

13.

Install the air-cleaner assembly.

17

 

Содержание 08781





















Отзывы: