Topex Voxell LCR Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 60

Topex Voxell LCR Скачать руководство пользователя страница 51

INSTALLATION MANUAL

page 51 / 60

Programmings of action upon incoming calls form GSM:

- should you want the calls coming in from the mobile network to be REJECTED: you dial

220

- if you want the calls coming in from the mobile network to be sent to the analog

telephone interface (the default setting) : you dial 221. By default, the calls coming in from the

GSM network are routed to one of the FXS or FXO interfaces.

Programming of action upon calls getting out through GSM:

- the outgoing calls from the analog interface are rejected : you dial 230

- the outgoing calls from the analog interface will be sent to the GSM network (the default

setting): you dial 231. Here again, the normal action is the default one – the outgoing calls are
routed via GSM module. Using the OAM program, you can also reject all outgoing calls, or

selectively reject certain phone number or prefixes.

Programming of enable/disable of progress tone for calls going out via GSM:

- enable: you dial 251

- disable (the default state): you dial 250

Programming of polarity during the call:

- if you want the polarity to be REVERSED during the call as compared to the other states

of a call (the default setting ): you dial 371

- if you want the polarity to remain the same during the call as it was during the other

states of a call: you dial 370

Programming of “power denial”:

You can select to generate or not line voltage on the subscriber port, while the GSM module is not
registered with the mobile network. If the line is not powered, the user won't be able to dial while
the module is not registered:

- for the duration while the GSM module is not registered, no line voltage will be generated

over the FXS port: you dial 301

- line voltage will always be provided for the port type FXS, even when the GSM module is

not registered with the mobile network (the default state): you dial 300

Programming of loopbreak:

- when a call ends, Voxell LCR generates a loop break for the duration set by the

loopbreak timer: you dial 311

- no loop break is generated upon the ending of a call (the default state) : you dial 310.

Programming of hotline:

- enable : you dial 321

- disable (the default state, hotline service is disabled) : you dial 320

Programming of “minute minder” signal:

- no generating - you dial 330

- to generate minute minder, you dial 331. Here also, the default state is with minute

minder NOT active.

«
...
49
50
51
52
53
...
»

Содержание Voxell LCR





























































Отзывы:

Нет отзывов