Topcon Pocket-3D Скачать руководство пользователя страница 76

Страница: 76 / 316

Setup Menu

Pocket-3D Reference Guide

2-30

Figure 2-41. Setup/Image Tabs for Total Station

On the

Advanced

dialog box (for prism sensors only), select how you

want to connect the total station (Figure 2-42 on page 2-31), then
press

Next

• Cable in STD mode – select to connect the total station via serial

cable or Bluetooth if the total station is in STD (standard)
measurement mode.

• Cable in Ext. Link mode – select to connect the total station via

serial cable or Bluetooth.

• RC4 Modem (Ext.Link) – select to connect the total station via

RC4 modem if the total station is in external link mode.

• Remote Control – select to connect the total station via serial

cable or Bluetooth if the total station is in external link mode.

• Baud rate – select either

600, 1200, 2400, 4800,

9600

• Data Bits – select either

• Stop Bits – select either

• Parity – select either

Odd

Even

NOTE

For a conventional total station, the GTS 200 for
example, you can only connect via Cable in
Standard Mode.

Содержание Pocket-3D





























































































































































































































































































































Результаты поиска

Содержание Pocket-3D

Отзывы:

Topcon Pocket-3D, Справочное руководство, Страница: 76 / 316

Результаты поиска

Содержание Pocket-3D

Отзывы: