Topcon Pocket-3D Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 316

Topcon Pocket-3D Скачать руководство пользователя страница 24

Installing Pocket-3D

Pocket-3D Reference Guide

1-2

Guide to Installing Pocket-3D

Pocket-3D installs on any hand-held controller that runs the Windows
Pocket PC operating system, including Topcon’s FC236. Pocket-3D
initially loads onto your computer, then uses Microsoft®
ActiveSync® to synchronize with the controller and install Pocket-3D
onto the controller. ActiveSync is available for free from the
Microsoft website (www.microsoft.com) and must be installed on the
computer before installing Pocket-3D.
The Pocket-3D program for your hand-held controller is located on
the 3DMC CD. It will first be loaded onto your computer, then
ActiveSync will install it onto your controller.
1. Connect your computer and hand-held controller.



Because ActiveSync will automatically install Pocket-3D once it
has been loaded onto the computer, this step is can be performed
at any time.

2. Insert the 3DMC software CD into the computer CD drive of the

computer. Navigate to the CD’s files using Explorer and open the
Pocket-3D folder.

3. Click the Pocket-3D setup icon to run the install program and

click

Next

on the

Welcome

screen (Figure 1-2).

Figure 1-2. Begin Pocket-3D Installation

«
...
22
23
24
25
26
...
»

Содержание Pocket-3D





























































































































































































































































































































Отзывы:

Нет отзывов