Topcon Pocket-3D Скачать руководство пользователя страница 281

Страница: 281 / 316

Stake-out

P/N 7010-0628

4-55

(Figure 4-82).

Figure 4-82. Vertical Surface Offset

Options

To view or change options for stake-out measurements, tap

Survey



Stake-out



Options

(Figure 4-83).

Figure 4-83. Survey



Stake-out



Options

On the

stakeout options

dialog box, select the desired options for

stakeout measurements, cut sheet, and audio, then press

(Figure 4-84 on page 4-56).

Measure

tab

sets the way to measure/stake-out points and alignments

and the information to display on the main screen during a
measurement/stake-out.

• Press ENTER to measure – enable to use the Enter key (on the

controller’s casing, below the display screen) to start the
measurement on each stakeout point or alignment.

Содержание Pocket-3D





























































































































































































































































































































Результаты поиска

Содержание Pocket-3D

Отзывы:

Topcon Pocket-3D, Справочное руководство, Страница: 281 / 316

Результаты поиска

Содержание Pocket-3D

Отзывы: