Tomy FLS-1000 Скачать руководство пользователя страница 25

Страница: 25 / 64

ー 24 ー

5. OPERATION

5-1. Turning On/Off the Power Switch

WARNING

Do not touch the power switch with a wet

hand.

●

Failure to do so may cause electric shock.

Check that the power supply is correctly

connected and the protective grounding is

properly provided.

To turn on the power, press the main power

switch to the [Ⅰ] “ON” position.

The control program version appears in the time

display on the control panel.

To turn on the power

①

②

Press the power switch to the [

○

] “OFF” position.

※

Check that the IN PROGRESS indicator on the control panel turns off or the COMPLETED

indicator in the work monitor display flashes.

To turn off the power

①

Operating parameters of the previous operation will be displayed in approximately 10

seconds.

③

STOP

MEMORY

STERILIZE

LIQUID

START

FUNCTION

CHECK

TIMER

EXT.

SENSOR

COOLING

FAN

EXHAUST SPEED

FAST

TIME

TEMPERATURE

TIMER

STERILIZE

LID

WATER

DRAIN

COVER

CHANGE WATER

°C

SLOW

STERILIZE

IN PROGRESS

Содержание FLS-1000

































































Результаты поиска

Содержание FLS-1000

Отзывы:

Похожие инструкции для FLS-1000

Бренды по названию

Популярные бренды

Tomy FLS-1000, Руководство оператора

Результаты поиска

Содержание FLS-1000

Отзывы:

Похожие инструкции для FLS-1000

Бренды по названию

Популярные бренды